openrcforums

I had a look at 'kaos-nano (PPM).eepm'. Did you realize, that throttle (ch1) is at least 50% open (with ID0, even higher with ID1 and ID2) as long as throttle cut is disabled? Therefore I suppose you did bind with throttle cut enabled (ch1 at 0%)? (throttle channel has to be at 0% for arming) Maybe ...

Hi, I don't have a model file for the nano CP S but for the basics here my model file for nano CP X: nano CPX.eepm Note: NO handling for panic mode as the X doesn't have this feature ID2 = Idle Up, ID0 and ID1 = stunt mode limits on CH6 are set to avoid too much pitch (have to be set individually fo...

Have you seen this post?
If you are familiar with soldering iron and xacto knife then this mod should be no big problem.
And it's worth the effort 'cause a reboot during flight is NOT a 'must have'!

Klaus

Why not changing only the label?

- save/restore single models to SDcard
- save/restore eeprom to SDcard (in development yet)

Klaus

Thank you for enlighting this mystery

I think about adding sliders to my 9Xtreme so I stumbled over this: In hardware menu the options for POT4 and POT5 are EXT1 to EXT4. Am I right that EXT1 to EXT4 for the pots are the 4 inputs formerly for the gimbals whereas EXT1 to EXT8 for the switches/push buttons are the 8 inputs formerly for th...

As far as I know the 9Xtreme board tests at every power on
whether the slave firmware is present (on the 9X board) or not.
If not, it (the 9Xtreme board) flashes the 9X board with the required firmware.

Klaus

Just had a look at eePe a few seconds ago and it's the same ...
ER9X i cannot test 'cause I have no radio at hand at the moment.

For those things it would be nice if we could reduce simulation speed (e.g. by 1/2,1/5,1/10,...) in eePskye, wouldn't it? (Or is it possible and I missed it?) What puzzled me a bit is the fact that to delay the activation of a switch (in the mixer) we need to set the down delay. I had expected to us...

Maybe the following can work: Note: the duration of the 1-shot at L4 and L5 must be longer than the delay for CH6 in the mixer.
If not, CH6 doesn't send a pulse to activate agility mode.

I cannot test it myself, 'cause one motor of my nano QX is suffering ...

Klaus

I don't know about OpenTX and CompanionTX. With eePe and eePskye it isn't possible to drag and drop mix lines but it should be possible to copy whole models from eePe to eePskye. I tried this a few minutes ago, but eePe crashed while dragging. as a workaround use copy and paste in the 'file' menu. Y...

I think of two possibilities: it's just as João posted: The nano QX changes into full agility mode only when the sticks are (nearly) centered... This can be solved by forcing ch2 and ch3 to 0% for a short moment before activating agility Change to agility mode is suppressed as long as a movement is ...

Does the nano QX change its color from blue to red when you try to flip?

mcometa wrote:And so I tested it...

João's or my version?

mcometa wrote: ...and the quad does nothing...

what means nothing? No reaction at all or just slipping away in the pointed direction?

Klaus

jhsa wrote: bool.. what?? What's that? ...

Boolean algebra is the algebra of AND, OR, XOR ... in conjunction with binary numbers ...
For further questions ask Mr. George Bool

(N.B. There should be a reset/clear all menu somewhere in the Logical Switches page. When you have all the values up and you can't figure out and just want to reset do it all over again you wanna hit this "ahhhhh s***!" button. Also a copy/move is helpful :D) Yeah, I think I suggested tha...

jhsa wrote:Klaus, a simplified version of your idea.. Save a couple logical switches ...

Yeah, that's true.

Sometimes I hardly struggle with this boolean algebra...

Klaus

Tested it (my solution) on the bench with my Nano QX and worked OK so far (no flight test!!!).
But to be able to change stabilty mode manually (with trainer switch) I would recommend to add
+R 100%Full Switch(TRN)
to channel 6 ...
Note the replace option!

Klaus

And don't forget: 100% spektrum equals to 80% erSKY9x.
So the limits should be set to +/- 80 except throttle low (for arming): Klaus

I'm not very familiar with all this new switch options but here is what I would try: Nano.jpg L1 is active when |ail| > 98 L2 gives a peak of 0.2 sec when L1 goes active L3 gives a peak of 0.2 sec when L1 goes inactive L4 combines L2 and L3 Same with L5 to L9 but ele LB combines L4 and L9 So use LB ...

As far as I understand he needs a low-high-low transition when the stick value reaches a threshold
to activate agility mode (and make e.g. a flip possible)
and another low-high-low transition when stick value then gets lower than the threshold
to enter stability mode

Klaus

Hi João,

a problem would be that the Nano QX is switched between 'agility' and 'stable'
by a toggle (momentary) switch (e.g. the trainer switch) on Channel 6.

And therefore if the Nano QX misses a switch transition he will get into trouble ...

Klaus

Hi Mike, I never used the print function but the posts of 'gerhardp' in "er9x development" about print function in eepe made me curious. So I tried it with eepskye. I found that using this function causes eepSKYe to crash when sticky throttle cut (safety switch type 'X') of the selected mo...

Same with me.
Worst thing: discard someting that's not used for veeeerrrryyy long, ... ... ... ... then you will need it a few days later ... (lex murphy)

That's one secret of a good hobbyist: use ev'rything you get your hands on (of course it must be suitable )

Simply put together a shashlik skewer, shashlik skewer.jpg a needle, needles.jpg a piece of wire and shrinking tube (maybe some CA glue, too) and you have an excelent probe for smd parts. Things you probably find in most households... (Don't try to solder the wire to the needle, in most cases that's...

jhsa wrote:... Quite expensive though ...

Divided by the years I have this pen I think much more went down the toilet for this hobby

Klaus

Exactly!

Klaus

Hi João,

this pen is called "Glasfaser-Radierer".
You can get it e.g. at amazon or ebay.

Klaus