openrcforums

I 'm not sure I understand it - but thanks for the work Mike !
regards
Hans

Hi Mike
Amazingly rapid response - whats more its positive - ErSky9x provides the answer again
Great work Mike
I'll follow your instructions
Many many thanks
Hans

Hi Guys I have been following the youtube video (https://www.youtube.com/watch?v=nZxMvTCN_pI) showing how this can be done with Open TX ie send the RSSI value back to TX via telemetry return it to the RX via 2.4Ghz then through to the FC and OSD via SBUS Open TX provides an inputs page to source RSS...

Thanks for the explanation Mike - that makes sense now

Anyhow its all working well for me on the 9Xtreme

Thanks for all your hard work
regards
Hans

Hi Mike/Joao Hope you are well Another couple of quick questions:- I'm using eePeSKY R421 Nov 21 2016, and when looking at the safety switch inputs I have noticed a new pop up box in the right hand column When I select sticky X in the second box there is a pop up giving Thr or P1,2,3 options - how d...

HI Joao Thanks for the super quick response and great explanation - I should have read the manual a little more carefully! It makes sense now and I will give it some thought and practise I'm still having a great time with the 9Xtreme and I'm glad to see you are still always present on the forum Than...

Hi Mike/Joa Hope you are well - I have a quick question I'm using the Extreme Board on the Turnigy 9X with ersky9x-r218, v 3531-Mike I am using an old model mix for elevator /throttle trim - relevant lines shown as follows:- CH2 source Ele wt 100 source CH7 wt 50 switch ID- CH3 source Thr wt 100 CH7...

This is my setup

CH2 source Ele wt 100
source OP7 wt 50 switch ID-
CH3 source Thr wt 100
CH7 source Thr wt 100 offset 100
source P3 wt -100 multiply

ID switches on elevator trim and throttle linkage
P3 varies the amount of down trim that is applied by throttle

Had an issue with login into the forum. Message was "Catchable fatal error: Argument 1 passed to phpbb\notification\type\base::__construct() must implement interface phpbb\db\driver\driver_interface, instance of phpbb\user_loader given, called in /var/www/html/openrcforums.com/forum/cache/prod...

bob195558 wrote:Hi lancaster,

Can you link to where these New FrSky Hall Effect Gimbals are (can be found) ?

Bob B.

Hi Bob

The gimbals are also shown on the Banggood site

https://goo.gl/hCkeFg
Hans

Hi Guys

Can these gimbals be fitted to the T9X Extreme?

regards
Hans

Have you tried flashing the both the TX and RX with International firmware

Hi Joao

I installed the resistor as shown on Mike photo

I thought it was pin 5 but now I see its pin 1

I will test for servo control as you say

thanks
Hans

Hi Guys

I have installed the 100 ohm resistor on both my 9Xtreme TXs and everything appears to be working ok.

Am I correct in thinking that because the resistor is in line to module pin no 5, good values for the RSS1 and SWR value indicate that all is working as it should ?

regards
Hans

Hi Joao
Hope you are well

Thanks for the super quick reply

I will do the PPM mod to be safe on both my T9XExtremes ( I recently bought a second Extreme board as the numbers are going down below 100!)

regards
Hans

Hi Guys Some weeks ago I updated my firmware to EU LBT versions on the XJT module and my XR receivers with no problems (SP Extreme board installed in T9X) The RX update requires leads to be connected between the SPort on the RX and the module pins numbers 3,4 and 5 in the TX. But thinking back on th...

Smiithy89 wrote:what would happen if the safety switch was knocked when the model is flying would the motors shut off and model drop to earth ? , Dan

If a Pot is used to arm the throttle then it can't be knocked on or off - much safer than a switch

Hi Guys
Its encouraging to hear from Steven that another run might be possible

HobbyKing are selling the 9X in Europe and in the UK and I noticed that Banggood are marketing the Flysky 9X

There is still a future for the 9X

regards Hans

MikeB wrote:The resetting code will be included in releases, and there is a count of how many resets have occured. This count is displayed on a "Debug" menu.

Mike.

Thanks Mike - thats good to know

Remind me how we get into the 'Debug' menu

regards
Hans

Thanks Octavios for the link. That gives me a good place to start. Also I see there are processor upgrade options but I'm not sure they're relevant with the 9Xtreme addon board installed. I have reading to do. I'm not giving up on this radio just yet. So far it has worked flawlessly for me. I just ...

Certainly not... the 9XR-Pro is however on sale and even cheaper at £53.19!! But the 9X comes with a module and receiver that can be easily modified by replacing the TX antenna with the antenna on whatever module is selected This gives a much more adaptable final product when using ERsky and the 9X...

octavios
sorry to get you exited but I thought £55.83 was a great price!
regards
hans

Hi Guys Now Hobbyking are finally selling the 9X including RX and module in the UK for a great price , lets hope people realise what a bargin it is - especially when fitted out with the 9Xtreme and Ersky firmware and also lets hope sales of the 9xtreme then pick up I for one will be getting a second...

Joao and Mike Thanks for the quick replies and suggestions I suspected the pogo connections might be the culprit The fault might be linked to periods when the TX has not been used or perhaps subjected to recent temperature changes It makes sense now you have explained how the gimbals have a direct p...

Hi Steven
I am planning to order a second board in the next few weeks
regards
Hans

Hi Guys I have encountered a slightly worrying random fault with 9Xtreme as follows :- Very occasionally all the navigation keys stop working apart from the exit button, which surprisingly triggers my elevator high/low voice warning. When in this state, all flight controls work normally apart from t...

Hi Joao
Glad to hear you fixed the problem
happy flying
regards
Hans

Hi Birdman

I attach some information about the 9 pin connectors I used

Thanks to Joao for this

regards
Hans

Hi Steven I dont think the Turnigy 9X is in widespread use in the UK but there might be more customers to come if people were made aware of the great combination of the 9X, the Extreme board and Ersky9X. I notice that HobbyKing are now selling the T9X package (Tx,module & Rx) in both the Europea...

Hi Dave

Have you tried the videos from Drone Shop? https://www.youtube.com/watch?v=AnDTJ0bwG2E

Various files are available somewhere on these links

regards
Hans