Search found 2394 matches

by bob195558
Fri Jan 08, 2021 11:06 pm
Forum: General help (FrSky Taranis radio)
Topic: Broke my early Tatanis. Help!
Replies: 8
Views: 4455

Re: Broke my early Tatanis. Help!

I have "erskyTx for Taranis" on my Taranis x9d and I use "eepskye for Windows" and I like it a lot and have no troubles.
You would use "eepskye for MAC".

If you think you would like to try it, find it here: http://www.er9x.com/
by bob195558
Fri Jan 08, 2021 10:53 pm
Forum: Hardware
Topic: Turnigy 9x Dual module (?)
Replies: 7
Views: 5236

Re: Turnigy 9x Dual module (?)

I am not sure, but I believe the size of the chip is to small to hold the firmware needed to do so. Maybe with the upgrade to the ATMEGA2561-16AU CPU Chip, it may be able to: https://openrcforums.com/forum/viewtopic.php?f=95&t=3819&start=120#p74105 Mike B. will know right-away. I know the 9X...
by bob195558
Tue Dec 22, 2020 11:48 am
Forum: FrSky Taranis radio
Topic: FrSky Enhanced Receiver Antenna
Replies: 8
Views: 7009

Re: FrSky Enhanced Receiver Antenna

Some info here: How do Antennas work ? : (https://www.youtube.com/watch?v=fSoXIqBlg9M&t=610s). Antenna theory: The FrSky receiver antenna puzzle (part 1): (https://www.youtube.com/watch?v=WBE_KqqHbM0&t=183s), The Fresnel Zone explained: (https://www.youtube.com/watch?v=xCVd3QGQhKU), RF power...
by bob195558
Tue Dec 15, 2020 3:55 pm
Forum: RF MODULES
Topic: Spectrum Analyzer RF Explorer 3G+ IoT for Raspberry Pi
Replies: 0
Views: 5926

Spectrum Analyzer RF Explorer 3G+ IoT for Raspberry Pi

This Spectrum Analyzer, RF Explorer 3G+ IoT that works with a Raspberry Pi and looks a lot more affordable then the RF Explorer 6G COMBO+ which cost about $400, though the 6G COMBO+ has more capability's. http://j3.rf-explorer.com/182 http://j3.rf-explorer.com/menu-models ( Some kind or error, becau...
by bob195558
Tue Dec 01, 2020 10:15 pm
Forum: Hardware
Topic: Turnigy 9x burned pad
Replies: 8
Views: 5788

Re: Turnigy 9x burned pad

Full Editor and then Attachment
by bob195558
Wed Oct 07, 2020 11:22 am
Forum: Turnigy 9XR PRO radio
Topic: Banggood 4in1 module, Flysky AFHDS2A and Telemetry
Replies: 189
Views: 120408

Re: Banggood 4in1 module, Flysky AFHDS2A and Telemetry

Found this info: https://www.flysky-cn.com/cat01-canshu Product Model: FS-CAT01 Product name: Altitude sensor Altitude measurement range: 0 ~ 8000m / 40 ~ 100kPa Power: 4.0 ~ 8.4V Data port: i.bus / (sens) Temperature range: 0 ℃ — + 60 ℃ Humidity range: 20% -95% Dimensions: 31 * 15 * 8.5mm Weight: ...
by bob195558
Sat Sep 19, 2020 9:00 am
Forum: Turnigy 9XR PRO radio
Topic: Did I erase my radio/chip? Or just fry a regulator?
Replies: 21
Views: 14166

Re: Did I erase my radio/chip? Or just fry a regulator?

erSkyTx also works on other radios, I use erSkyTx on my Taranis x9d: http://www.er9x.com/
by bob195558
Sat Sep 12, 2020 8:39 am
Forum: Turnigy 9XR PRO radio
Topic: Did I erase my radio/chip? Or just fry a regulator?
Replies: 21
Views: 14166

Re: Did I erase my radio/chip? Or just fry a regulator?

Some more info here about replacing the processor, if needed.
Upgrading to the ATMEGA2561-16AU CPU Chip: https://openrcforums.com/forum/viewtopi ... 120#p74105
by bob195558
Sat Sep 12, 2020 12:07 am
Forum: 3D Printing
Topic: Linear Y-axis Rail Upgrade (CR10 3D Printer)
Replies: 1
Views: 6768

Re: Linear Y-axis Rail Upgrade (CR10 3D Printer)

Also see these mods:

Increase Y-axis Print-Bed Travel Mod (CR10 3D Printer): https://openrcforums.com/forum/viewtopi ... 29&t=12325

Simple way make your own Solid-Bed-Mounts (3D Printing): https://openrcforums.com/forum/viewtopi ... 29&t=12851
by bob195558
Fri Sep 11, 2020 1:50 pm
Forum: 3D Printing
Topic: Linear Y-axis Rail Upgrade (CR10 3D Printer)
Replies: 1
Views: 6768

Linear Y-axis Rail Upgrade (CR10 3D Printer)

Because the print-bed surface is weak from side to side, and can be easily tipping down with very light pressure especially when printing large tall parts, this upgrade fixes this trouble. Linear Rails Y axis MGN12H_e.jpg I purchased this kit through Amazon "JS 1set CR-10S Light Weight MGN12H L...
by bob195558
Wed Sep 09, 2020 2:37 am
Forum: openTx
Topic: Turnigy 9x updated and now THR RUD and AIL switches are always on
Replies: 11
Views: 6543

Re: Turnigy 9x updated and now THR RUD and AIL switches are always on

Opentx is not supported anymore for a very long time now.
er9x is still supported and so is up to date and works a lot better then the very old Opentx for your 9x radio.

Glad you have your 9x working properly !

This may be helpful for you:
https://openrcforums.com/forum/viewtopic.php?f=5&t=6473
by bob195558
Tue Sep 08, 2020 1:07 pm
Forum: openTx
Topic: Turnigy 9x updated and now THR RUD and AIL switches are always on
Replies: 11
Views: 6543

Re: Turnigy 9x updated and now THR RUD and AIL switches are always on

Hi all I tried to revive my old turnigy 9x with 64 Atmega but maybe I did something wrong 'cos now THR RUD AIL buttons doesnt' work anymore remaining in activate state. So, you only troubles with the pots ? I tried to flash 2.0 and 2.1 with and without frsky option without solving now I am openttx ...
by bob195558
Mon Sep 07, 2020 10:29 pm
Forum: openTx
Topic: Turnigy 9x updated and now THR RUD and AIL switches are always on
Replies: 11
Views: 6543

Re: Turnigy 9x updated and switchs go mad

"switch problem" Sounds like maybe Calibration is not correct yet.
Some times you need to try doing it several times.
Do you have the "Calibration" procedure ?
by bob195558
Tue Sep 01, 2020 1:56 pm
Forum: openTx for FrSky radios
Topic: RSSI alarm
Replies: 2
Views: 3525

Re: RSSI alarm

Hi heliperry ,
I use erSkyTx so not able to help,
maybe some one who uses opentx will help you soon.
You may find the info you are needing here: https://openrcforums.com/forum/viewforum.php?f=45

Maybe consider flashing to erSkyTx, it is great firmware too: http://www.er9x.com/
by bob195558
Thu Aug 27, 2020 7:40 pm
Forum: 3D Printing
Topic: Quick editing of Supports with the Simplify-3D slicer
Replies: 7
Views: 6785

Re: Quick editing of Supports in Simplify-3D slicer

I think it is a Geeetech I3 with a build volume of: 200 x 200 x 180mm.
Looks good !
by bob195558
Thu Aug 27, 2020 10:29 am
Forum: Hardware
Topic: Bad Eeprom error. 9xtreme/encoder.
Replies: 36
Views: 20343

Re: Bad Eeprom error. 9xtreme/encoder.

Suggest, maybe it could be a hardware problem. If you have a bad switch or a bad chip it could be causing the troubles. Many years ago I had a new 9x that bricked when programing it and later found the selecting switches were corroded. After replacing several of the selecting switches, it worked OK.
by bob195558
Thu Aug 27, 2020 2:28 am
Forum: 3D Printing
Topic: Quick editing of Supports with the Simplify-3D slicer
Replies: 7
Views: 6785

Re: Quick editing of Supports in Simplify-3D slicer

:lol: I liked that also ! :D

What model 3D Printer did you receive ?
by bob195558
Wed Aug 26, 2020 11:52 am
Forum: 3D Printing
Topic: Quick editing of Supports with the Simplify-3D slicer
Replies: 7
Views: 6785

Quick editing of Supports with the Simplify-3D slicer

In the Simplify-3D slicer program you can now quickly edit the Supports you do not want after Simplify-3D has auto apply hundreds of unwanted supports. See the video here: https://www.youtube.com/watch?v=AiZdsH0RuBI&feature=youtu.be&fbclid=IwAR14roJxNoxAvbGj8wSp3PBkrPLHkiRZ1tSGEqoSq9PDNUTDcT...
by bob195558
Sun Aug 23, 2020 12:23 am
Forum: FrSky Taranis radio
Topic: X9D Plus 2019 SE not transmitting
Replies: 3
Views: 3150

Re: X9D Plus 2019 SE not transmitting

I upgraded my Taranis x9d with the Hall-effect gimbals and they work great. I also use erskyTx for Taranis firmware. I have been using it for a long time, you can find it here: http://www.er9x.com/ FrSky did have some troubles with some of there early internal modules. I have found using the externa...
by bob195558
Sun Aug 23, 2020 12:14 am
Forum: erskyTx (was ersky9x)
Topic: ErskyTx Test Versions
Replies: 141
Views: 296862

Re: ErskyTx Test Versions

Look for erskyTx for Taranis
I have been using it for a long time, find it here: http://www.er9x.com/
If you have any troubles ask for help, but I think you will have none as it runs very very well !
Use eepSkye on your computer instead of er9x.
by bob195558
Sun Aug 23, 2020 12:05 am
Forum: er9x
Topic: Turnigy 9x with 2 modules
Replies: 9
Views: 6775

Re: Turnigy 9x with 2 modules

Also see here about "9x Radio Rebooting Problem Horizontal Trims Digital Ground Fix"
https://openrcforums.com/forum/viewtopi ... 120#p69475
by bob195558
Fri Aug 21, 2020 1:36 pm
Forum: er9x
Topic: Er9x NEW User's Manual
Replies: 66
Views: 203036

Re: Er9x NEW User's Manual

Maybe upgrading to the ATMEGA2561-16AU CPU Chip ?: https://openrcforums.com/forum/viewtopi ... 120#p74105
by bob195558
Wed Aug 19, 2020 10:47 pm
Forum: er9x
Topic: Turnigy 9x processor upgrade
Replies: 24
Views: 15321

Re: Turnigy 9x processor upgrade

Did not know if you saw this,
if not this info may have been a help for you: https://openrcforums.com/forum/viewtopi ... 120#p74105

Upgrading the 5V regulator would be a good help too: https://openrcforums.com/forum/viewtopi ... =95&t=3819
by bob195558
Tue Aug 04, 2020 1:11 pm
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: 3D printable case for GPS/Vario sensor
Replies: 8
Views: 5720

Re: 3D printable case for GPS/Vario sensor

Hi Emanuel, Looks good, well done ! :) OpenXsensor GPS Case_1c.jpg I use Simplify 3D slicer and I have been trying to separate the two parts without success. I would like to try printing the top cover on it's side as I believe would then be able to print without supports. OpenXsensor GPS Case_1b.jpg...
by bob195558
Tue Aug 04, 2020 10:48 am
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: 3D printable case for GPS/Vario sensor
Replies: 8
Views: 5720

Re: 3D printable case for GPS/Vario sensor

Hi Emanuel,
The link does not work correctly or something ?
(404 YOU HAVE REACHED THE END OF THE THINGIVERSE).

Also maybe good to post it here "3D Printing": https://openrcforums.com/forum/viewforum.php?f=129
by bob195558
Tue Aug 04, 2020 12:26 am
Forum: er9x
Topic: Turnigy 9x processor upgrade
Replies: 24
Views: 15321

Re: Turnigy 9x processor upgrade

More features in the firmware.
You will like the upgrade.
by bob195558
Mon Aug 03, 2020 11:12 am
Forum: General help (FrSky Taranis radio)
Topic: Placement of Dual Antennas
Replies: 1
Views: 2076

Re: Placement of Dual Antennas

Normally one in horizontal and the other one vertical is recommended.
Hard to say what is the best for your setup.

Go to advanced search