Search found 553 matches
- Sun Jan 10, 2016 7:39 pm
- Forum: ersky9xr
- Topic: Model Setup Help?
- Replies: 45
- Views: 36972
Re: Model Setup Help?
I had a look at 'kaos-nano (PPM).eepm'. Did you realize, that throttle (ch1) is at least 50% open (with ID0, even higher with ID1 and ID2) as long as throttle cut is disabled? Therefore I suppose you did bind with throttle cut enabled (ch1 at 0%)? (throttle channel has to be at 0% for arming) Maybe ...
- Sun Jan 10, 2016 9:14 am
- Forum: Template Library
- Topic: Blade Nano CP S
- Replies: 22
- Views: 35646
Re: Blade Nano CP S
Hi, I don't have a model file for the nano CP S but for the basics here my model file for nano CP X: nano CPX.eepm Note: NO handling for panic mode as the X doesn't have this feature ID2 = Idle Up, ID0 and ID1 = stunt mode limits on CH6 are set to avoid too much pitch (have to be set individually fo...
- Sat Jan 09, 2016 6:42 pm
- Forum: er9x
- Topic: Eeprom issue while trim
- Replies: 8
- Views: 6070
Re: Eeprom issue while trim
Have you seen this post?
If you are familiar with soldering iron and xacto knife then this mod should be no big problem.
And it's worth the effort 'cause a reboot during flight is NOT a 'must have'!
Klaus
If you are familiar with soldering iron and xacto knife then this mod should be no big problem.
And it's worth the effort 'cause a reboot during flight is NOT a 'must have'!
Klaus
- Sat Jan 09, 2016 12:18 am
- Forum: erskyTx (was ersky9x)
- Topic: ERSKYTx (was ersky9x) Questions
- Replies: 2347
- Views: 1349488
Re: ERSKY9x Questions
Why not changing only the label?
- Fri Jan 08, 2016 5:18 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKY9X Coding
- Replies: 4540
- Views: 1974071
Re: ERSKY9X Coding
- save/restore single models to SDcard
- save/restore eeprom to SDcard (in development yet)
Klaus
- save/restore eeprom to SDcard (in development yet)
Klaus
- Fri Jan 08, 2016 4:16 pm
- Forum: 9Xtreme upgrade board
- Topic: Question concerning POT4 and POT5
- Replies: 2
- Views: 2525
Re: Question concerning POT4 and POT5
Thank you for enlighting this mystery
- Fri Jan 08, 2016 3:59 pm
- Forum: 9Xtreme upgrade board
- Topic: Question concerning POT4 and POT5
- Replies: 2
- Views: 2525
Question concerning POT4 and POT5
I think about adding sliders to my 9Xtreme so I stumbled over this: In hardware menu the options for POT4 and POT5 are EXT1 to EXT4. Am I right that EXT1 to EXT4 for the pots are the 4 inputs formerly for the gimbals whereas EXT1 to EXT8 for the switches/push buttons are the 8 inputs formerly for th...
- Fri Jan 08, 2016 3:47 pm
- Forum: 9Xtreme upgrade board
- Topic: Changement de carte mère surTGYX
- Replies: 10
- Views: 7658
Re: Changement de carte mère surTGYX
As far as I know the 9Xtreme board tests at every power on
whether the slave firmware is present (on the 9X board) or not.
If not, it (the 9Xtreme board) flashes the 9X board with the required firmware.
Klaus
whether the slave firmware is present (on the 9X board) or not.
If not, it (the 9Xtreme board) flashes the 9X board with the required firmware.
Klaus
- Fri Jan 08, 2016 3:41 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKYTx (was ersky9x) Questions
- Replies: 2347
- Views: 1349488
Re: ERSKY9x Questions
Just had a look at eePe a few seconds ago and it's the same ...
ER9X i cannot test 'cause I have no radio at hand at the moment.
ER9X i cannot test 'cause I have no radio at hand at the moment.
- Fri Jan 08, 2016 3:20 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKYTx (was ersky9x) Questions
- Replies: 2347
- Views: 1349488
Re: ERSKY9x Questions
For those things it would be nice if we could reduce simulation speed (e.g. by 1/2,1/5,1/10,...) in eePskye, wouldn't it? (Or is it possible and I missed it?) What puzzled me a bit is the fact that to delay the activation of a switch (in the mixer) we need to set the down delay. I had expected to us...
- Fri Jan 08, 2016 11:57 am
- Forum: erskyTx (was ersky9x)
- Topic: ERSKYTx (was ersky9x) Questions
- Replies: 2347
- Views: 1349488
Re: ERSKY9x Questions
Maybe the following can work:
If not, CH6 doesn't send a pulse to activate agility mode.
I cannot test it myself, 'cause one motor of my nano QX is suffering ...
Klaus
Note: the duration of the 1-shot at L4 and L5 must be longer than the delay for CH6 in the mixer.If not, CH6 doesn't send a pulse to activate agility mode.
I cannot test it myself, 'cause one motor of my nano QX is suffering ...
Klaus
- Fri Jan 08, 2016 11:30 am
- Forum: 9Xtreme upgrade board
- Topic: eepskye editor and the eepe editor
- Replies: 9
- Views: 7494
Re: eepskye editor and the eepe editor
I don't know about OpenTX and CompanionTX. With eePe and eePskye it isn't possible to drag and drop mix lines but it should be possible to copy whole models from eePe to eePskye. I tried this a few minutes ago, but eePe crashed while dragging. as a workaround use copy and paste in the 'file' menu. Y...
- Fri Jan 08, 2016 9:20 am
- Forum: erskyTx (was ersky9x)
- Topic: ERSKYTx (was ersky9x) Questions
- Replies: 2347
- Views: 1349488
Re: ERSKY9x Questions
I think of two possibilities: it's just as João posted: The nano QX changes into full agility mode only when the sticks are (nearly) centered... This can be solved by forcing ch2 and ch3 to 0% for a short moment before activating agility Change to agility mode is suppressed as long as a movement is ...
- Thu Jan 07, 2016 6:10 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKYTx (was ersky9x) Questions
- Replies: 2347
- Views: 1349488
Re: ERSKY9x Questions
Does the nano QX change its color from blue to red when you try to flip?
- Thu Jan 07, 2016 5:45 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKYTx (was ersky9x) Questions
- Replies: 2347
- Views: 1349488
Re: ERSKY9x Questions
João's or my version?mcometa wrote:And so I tested it...
what means nothing? No reaction at all or just slipping away in the pointed direction?mcometa wrote: ...and the quad does nothing...
Klaus
- Thu Jan 07, 2016 5:35 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKYTx (was ersky9x) Questions
- Replies: 2347
- Views: 1349488
Re: ERSKY9x Questions
Boolean algebra is the algebra of AND, OR, XOR ... in conjunction with binary numbers ...jhsa wrote: bool.. what?? What's that? ...
For further questions ask Mr. George Bool
- Thu Jan 07, 2016 5:08 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKYTx (was ersky9x) Questions
- Replies: 2347
- Views: 1349488
Re: ERSKY9x Questions
(N.B. There should be a reset/clear all menu somewhere in the Logical Switches page. When you have all the values up and you can't figure out and just want to reset do it all over again you wanna hit this "ahhhhh s***!" button. Also a copy/move is helpful :D) Yeah, I think I suggested tha...
- Thu Jan 07, 2016 5:03 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKYTx (was ersky9x) Questions
- Replies: 2347
- Views: 1349488
Re: ERSKY9x Questions
Yeah, that's true.jhsa wrote:Klaus, a simplified version of your idea.. Save a couple logical switches ...
Sometimes I hardly struggle with this boolean algebra...
Klaus
- Thu Jan 07, 2016 4:44 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKYTx (was ersky9x) Questions
- Replies: 2347
- Views: 1349488
Re: ERSKY9x Questions
Tested it (my solution) on the bench with my Nano QX and worked OK so far (no flight test!!!).
But to be able to change stabilty mode manually (with trainer switch) I would recommend to add
+R 100%Full Switch(TRN)
to channel 6 ...
Note the replace option!
Klaus
But to be able to change stabilty mode manually (with trainer switch) I would recommend to add
+R 100%Full Switch(TRN)
to channel 6 ...
Note the replace option!
Klaus
- Thu Jan 07, 2016 4:19 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKYTx (was ersky9x) Questions
- Replies: 2347
- Views: 1349488
Re: ERSKY9x Questions
And don't forget: 100% spektrum equals to 80% erSKY9x.
So the limits should be set to +/- 80 except throttle low (for arming): Klaus
So the limits should be set to +/- 80 except throttle low (for arming): Klaus
- Thu Jan 07, 2016 4:08 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKYTx (was ersky9x) Questions
- Replies: 2347
- Views: 1349488
Re: ERSKY9x Questions
I'm not very familiar with all this new switch options but here is what I would try: Nano.jpg L1 is active when |ail| > 98 L2 gives a peak of 0.2 sec when L1 goes active L3 gives a peak of 0.2 sec when L1 goes inactive L4 combines L2 and L3 Same with L5 to L9 but ele LB combines L4 and L9 So use LB ...
- Thu Jan 07, 2016 3:29 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKYTx (was ersky9x) Questions
- Replies: 2347
- Views: 1349488
Re: ERSKY9x Questions
As far as I understand he needs a low-high-low transition when the stick value reaches a threshold
to activate agility mode (and make e.g. a flip possible)
and another low-high-low transition when stick value then gets lower than the threshold
to enter stability mode
Klaus
to activate agility mode (and make e.g. a flip possible)
and another low-high-low transition when stick value then gets lower than the threshold
to enter stability mode
Klaus
- Thu Jan 07, 2016 3:12 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKYTx (was ersky9x) Questions
- Replies: 2347
- Views: 1349488
Re: ERSKY9x Questions
Hi João,
a problem would be that the Nano QX is switched between 'agility' and 'stable'
by a toggle (momentary) switch (e.g. the trainer switch) on Channel 6.
And therefore if the Nano QX misses a switch transition he will get into trouble ...
Klaus
a problem would be that the Nano QX is switched between 'agility' and 'stable'
by a toggle (momentary) switch (e.g. the trainer switch) on Channel 6.
And therefore if the Nano QX misses a switch transition he will get into trouble ...
Klaus
Re: eepSKYe
Hi Mike, I never used the print function but the posts of 'gerhardp' in "er9x development" about print function in eepe made me curious. So I tried it with eepskye. I found that using this function causes eepSKYe to crash when sticky throttle cut (safety switch type 'X') of the selected mo...
- Tue Jan 05, 2016 6:23 pm
- Forum: Hardware
- Topic: No Power: Flashing success turns to burned out brick failure
- Replies: 47
- Views: 19904
Re: No Power: Flashing success turns to burned out brick failure
Same with me.
Worst thing: discard someting that's not used for veeeerrrryyy long, ... ... ... ... then you will need it a few days later ... (lex murphy)
Worst thing: discard someting that's not used for veeeerrrryyy long, ... ... ... ... then you will need it a few days later ... (lex murphy)
- Tue Jan 05, 2016 6:12 pm
- Forum: Hardware
- Topic: No Power: Flashing success turns to burned out brick failure
- Replies: 47
- Views: 19904
Re: No Power: Flashing success turns to burned out brick failure
That's one secret of a good hobbyist: use ev'rything you get your hands on (of course it must be suitable )
- Tue Jan 05, 2016 5:22 pm
- Forum: Hardware
- Topic: No Power: Flashing success turns to burned out brick failure
- Replies: 47
- Views: 19904
Re: No Power: Flashing success turns to burned out brick failure
Simply put together a shashlik skewer, shashlik skewer.jpg a needle, needles.jpg a piece of wire and shrinking tube (maybe some CA glue, too) and you have an excelent probe for smd parts. Things you probably find in most households... (Don't try to solder the wire to the needle, in most cases that's...
- Sun Jan 03, 2016 3:51 pm
- Forum: er9x
- Topic: No joy with 9x transmitter and SmartieParts SP Basic firmware programmer for Er9x install
- Replies: 80
- Views: 44373
Re: No joy with 9x transmitter and SmartieParts SP Basic firmware programmer for Er9x install
Divided by the years I have this pen I think much more went down the toilet for this hobbyjhsa wrote:... Quite expensive though ...
Klaus
- Sun Jan 03, 2016 2:05 pm
- Forum: er9x
- Topic: No joy with 9x transmitter and SmartieParts SP Basic firmware programmer for Er9x install
- Replies: 80
- Views: 44373
- Sun Jan 03, 2016 1:57 pm
- Forum: er9x
- Topic: No joy with 9x transmitter and SmartieParts SP Basic firmware programmer for Er9x install
- Replies: 80
- Views: 44373