openrcforums

You can just put the SD in a reader and use companion's "read from radio" and "write to radio" as if the radio was connected.

I'm not aware of that being a model that exists, there's a G-RX8 and an RX8R, but...

Have you made sure the USB mode is set to Joystick? Did you check in the Joystick control panel that it was detected? Are things moving there? The first time Velocidrone recognized my Taranis controller, but only partially (I was only able to go left and right and that's it). It can't be recognised ...

That's what the manual says.

jhsa wrote: ↑Thu Mar 31, 2022 5:19 pm Power switch fails, and the radio will still stay on until I move the switch to the off position.

Well if the switch fails so as to do the exact same as if you moved it to the off position, how would the radio know you didn't?

Soft power helps IF the conditions are met i.e. they have a setup that provides telemetry and the option to keep on hasn't been disabled... we don't have enough info about the setup though

Yes you can connect battery voltage up to 36V straight to AIN2, then discover sensors on the radio and should be getting something.

What do you want to do on your computer?
To edit models/settings no driver is needed, there's an additional utility but it's only for flashing firmware in DFU/recovery mode which you should normally never need to do.

The DHT is just a DJT without a case, they work the same.

No such messages exists in companion as far as I know, and it works here. A screenshot of the actual error might help.
You might need to replace the libs as mentioned here:
http://www.open-tx.org/2021/10/01/companion-downloads

The number for "telemx" is the slot number on the left.
You might rather want to rename the sensors after their discorvery to something more descriptive and then use those names.

They're basically bits that say whether the sensor was received from the internal or external module and which receiver from each module. It's there mostly for the FrSky ACCESS system that can receive sensors from multiple receivers at the same time and thus there needs to be a way to differentiate ...

- Discovery never stops by itself
- There should not be duplicates, if there are either the sensor has timing issues or there's an issue with the library/implementation
- The number is the source (module/receiver) the sensor was received from.

You can use latest version, update both firmware and SD card, and then do a "factory reset", recalibrate sticks and you'll start ffresh as new.

It depends on the drone, not the radio. Can't say much without knowing what the drone is or what firmware it uses.

Not sure what the question is, but this usually depends on the aircraft and its configuration more than the radio.

Enter on home screen, it's in the same menu as Model Select.

No, no widget or countdown option for it.

There is a battery timer in the Statistics menu.

SM6002Ns are MOSFETS, not diodes. All 8 may not be identical, so be sure to check the type of the ones on the back. Could be that one failing took the others, but could also be a fault on the transformer or a serious instantaneous overload on the output. Does the PC / anything else that was connecte...

looks like you have multiple versions of companion installed and it's the old one that's registered to open .bin files in Windows.

Try ejecting once and then just unplug anyway.

You can update everything to ACCST2 but it's not possible to see what version's currently on things.

tonnie78 wrote: ↑Wed Dec 22, 2021 11:01 am I have also tried to update the firmware with the help of companion but it says it has a problem writing to drive E:

You likely have the radio on instead of bootloader mode.

For the data the microSD card might have a bad contact or have failed.

What's your cause for concern? It's the seller/importer's responsibility, not yours. As long as you buy one in the US then the seller will have made sure it's valid, and there have been multiprotocol radios sold there for quite a while.

If it's currently got the frsky factory firmware and you're sure you're flashing the correct file just disable the hardware check.

You totally can.

Means your memory is full, models aren't stored on the SD so the only thing is have fewer of them, use the "archive" function, or simplify them so they take less space (usage is written next to the names).

Only with an external module

Sorry, I think maybe I misunderstood. Is there a function to "discover sensors"? I never needed to do anything in my older Tx or Companion 2.2, the functions were available from the start by default in both. This system was introduced in 2.2 4 years ago. You had to have been on 2.1 to nev...

At least one of your models has broken settings with invalid sources. Don't know where those come from but you might want to fix or delete them. Companion shouldn't crash, we'll be looking into that but even if not something wrong can't be converted to anything that could be expected to be correct. ...