openrcforums

With the trims held in you're doing a short press of the power button and not a long one, right?

We know you've been doing that... but you're having issues, which can be understood from the way you've gotten there, and we're advising you on how to go about avoiding to get into that situation. You're obviously not interested in learning how it actually works or what are the good practices, so......

Making a global change in inputs or outputs would effect how all the flight modes operate. Why would I want to do that? Am I missing something? Now yes, that's why you'd want to adjust outputs first thing before setting up anything else to "calibrate" each servo's center and travel ranges...

Ideally: - How the response to a control input should be in inputs - How channels should ideally relate to each other in Mixes - Adjustments to take account of mechanical differences in outputs That way things are separated by intent and most things you'd need to tweak are restricted to only one of ...

You would adjust servo/linkage-specific things on the outputs page so as to separate this aspect from the mixes, you want those the same.

That's all perfectly normal. Drop is pretty quick to 3.7V/cell nominal around which it'll spend a good ~80% of the time to discharge.

xv1 wrote: ↑Mon Aug 22, 2022 12:34 pm despite being 3.7v batteries won't charge beyond 8.1v.

Did you actually measure them externally? Might be the radio calibration that needs adjusting instead.

Very unlikely they'd fail that quickly unless they were fakes.

That's handled at protocol level so it's likely a specificity of freedomTX/the code they wrote to talk to their module not implementing it.

It's not the input you want to duplicate, inputs are not tied to channels.
It's the mixer lines you have on CH2 you want to copy to CH6.

If you have touchscreen used then your radio is running EdgeTX, not OpenTX so you need to use EdgeTX tools.

If it has stock FrSky firmware make sure to select the correct radio type in companion and disable the compatibility check.

That's usually how it is, and is easy enough to test...

Telemetry is not control, you don't exactly need it.

You probably chose firmware for X9D+ instead of X9D.

If it works it works, if not you may need to try fiddling with the values until you find something that does...

Your copies are on the same channels as the originals, not on those you're going to connect your servos to, you probably want 5 and 6.
Outputs will need their own adjustments based on your servos/linkages to match both ailerons' centering and throws.

You can copy a line by long pressing enter on it, choose copy, then scroll it to where you want it.

You don't change anything in Inputs, and in Mixer you copy the line of the first channel onto the 2nd.

Receiver/module firmware don't even need to be in a FIRMWARE folder, they can be anywhere on the card. It's only radio firmware that you want to be able to flash from the bootloader that needs to be there.

cps wrote: ↑Sun Jun 12, 2022 5:37 am(I thought to have seen in the opentx source code that they always try to "unstuff" the s- and f-port telemetry packets... but I might be wrong...)

Yes because F-port is purely a receiver-side thing, it's not involved in the radio-side communications.

Likely hardware, the USB connection is detected by the 5V from the computer being present on the relevant pin. Might be a short / screwed up connection inside.

The screen reads 100, 0, -100 as I flip through the switch. If the channel monitor does show this then the radio correctly puts out 3 positions and you need to look elsewhere, either ELRS or the flight controller. Note that ELRS only supports 2 positions on some channels depending on configuration ...

Is the radio powered up in bootloader mode/trims in?
Do NOT use Zadig in that mode.

The RTC is in the main processor, no separate chip or external communication.

Show what you get with OpenTX 2.3.15, when switching to AFHDS3 you should see Module status quickly going from "Not Ready" to "Connecting" as it powers up. I tried with 2 TX16Ss with OpenTX 2.3.15 and it's fine on both. Tried ETX 2.7.1 on one of them and it never moved from "...

Current one.

Special Function, choose switch you want to use to play the value, Play Value, S2

If you want all cells you need a separate sensor like the FLVSS.

Ratio should be "the max measurable value" so yes 36. Never had one of those receivers but if they do it the same as the older ones the fact they've put a 1/10 divider would lead to terrible resolution/precision so wouldn't be worth more than a ballpark (36V as 256 steps = 0.14V / step, no...

You register with the button, then bind just by powering up without pressing the button.