openrcforums

did you unzipped tcl_lib.zip in the sam-ba folder tcl_lib (in my system /usr/local/bin/sam-ba/tcl_lib/)

In the simulator yes, it's the intended behavior...
On radio the things are different...

The problem is that those files were saved by a buggy version of c9x

Set the radio in D16 mode select a receiver id different from 0 press bind (the radio will beep)

Power up the receiver at a least 1m of distance from the radio while holding down the bind button.

power off the receiver exit from the model setup

power again the receiver on, it should be ok.

Thanks for highlighting,
bugs reporting is always welcome, we do our best for preventing them but sometimes they come out...
Regards,
Romolo

There was a bug in version 1.42.
previous gvars should be checked carefully
the problem apply only to files saved on the pc with previous version and not to eeprom read from radio.

the serialport is indeed /dev/ttyACM0

[53780.563189] cdc_acm 7-4:1.0: This device cannot do calls on its own. It is not a modem.
[53780.563233] cdc_acm 7-4:1.0: ttyACM0: USB ACM device

dmesg issued after you have connected the radio should be your friend.
normally is /dev/ttyACM0 or something similar

Already fixed we will release soon...

No for sky9x board you need sam-ba and related tcl_libs
With dfu-util it's a no go..

http://85.18.253.250/sam-ba/sam-ba_2.11.zip

and

http://85.18.253.250/sam-ba/tcl_lib.zip

Absolutely no bothy .bin .eepe can refer too eeprom too .eepe are a modified intel hex format of the eeprom .bin are raw binary images at the time of 9x was much more comfortable to use .eepe as the tool for writing (avrdude) was using Intel hex with sky9x and now with taranis we are using .bin as w...

Ok dudes,
even with 1024 steps, considering that the whole stick travel is about 5cm, we have that each step=5/1000= 0.05mm
So stop flying in the sky and go back with your feet on ground.
Has your thumb a positioning precision of 5 cents of millimeter ?
I really don't think so....

Actually no but, failsafe position are normally a serious thing to be set: in my idea you just need to set 4/5 channels 1) motor off 2) elevator up 3) rudder / ailerons for flat spin (depends on your model if it perform better right or left) Fail safe should not save the model but people. The model ...

You don't need tu turn the radio OFF (btw when is connected via USB it doesn't turn off)

The SD structure is changed again: in latest firmware is: SOUNDS\en\ as in a single SD card the radio allows to have multiple languages (change due mainly to taranis) About companion SD structure path To enable selection of files for functions like "background music" or "play track&qu...

in D16 mode the fail safe settings are supposed to be programmed by the radio. Fs are transmitted to the receiver every 9 seconds, so if you do the power off test before radio fs setting get transmitted to the RX you will probably get RX ones other way TX ones. The proper wa y to set failsafe in D16...

The radio for reading the eeprom should be turned on with all warning cleared before connecting to the PC:
Two drives will appear
Then you will be able to read the eeprom.

RTFM : http://code.google.com/p/opentx/wiki/Op ... ompanion9x

Because when you create a new memory it uses the value in preferences Instead if you want to modify the existing value on the radio you need to edit general settings of your radio and write it back. It's not companion asking it without no reason. It's you that have still not learned how to use the t...

About mac and the taranis:
we urge someone with issue on latest releases to run the following command ve companion 1.43

otool -L companion9x.app/contents/macos/companion9x

which firmware do you have on your taranis ?

where do you have the THR ?? on the left or on the right stick ??

You have selected wrong mode in general settings.

SR71 get 1.43 as soon will be available (short time)

Anyway have a look to PM...
or send me the list (i will ask you what is missing)

Ask him to send his eeprom...
Are we sure he not trying to bind the extarnal not existing module ?

Also did he opened the radio, maybe to change mode ?
(cables disconnected)

The difference is huge...

ppm_center moves the center but leaves the +/- travels the same by moving also the limits...
offset move the center but leave the limits where they are, so +/- travels get different.

no it's for taranis rev4a...
sorry... this one is correct

there is also another solution:
set a custom switch
cs1 a<x "timer1 < 30" and cs2 duration 0.5
cs2 TIM 0.5 0.5

then in custom function
cs1 play value " timer1" do not repeat

no programming skills required

The first is a feature and not a bug, so you are supposed to know where are you creating mixers....

Aabout GV: Please report the issue on the google code page
Following issue in different threads/forum is impossible!!
That's not the way to go.

Flaps, there is no need to use offset, use PPM center.
It's far better, it has been implemented also considering multiples servos (center at 1610)