openrcforums

it's automatically reset when you remove battery...
the bootloader is read only

may you try to flash the EN firmware just to see if it's not an issue with FR one ?
If you have problems getting the radio recognized by flash procedure, disconnect the battery,

I was in firmware 2667, the lcd does not come at all, only the backlite, if i remove the sd card nothing goes better, i've tried this morning to put the new firmware (2688) and now things are going worst, the radio is not recongnised by the computer, i can still flash it but can't acces to it when ...

Now I understand....
Renasas processor are those that power Fubaba radios.

This is a "Conspiracy"

João,
opentx has PPM_CENTER so that's not the problem...

BTW JR servo center at 1500 as well most china servos...

Well the center in c9x reflect the center in opentx the main problem is that if you need a non standard center (1520 is a standard for futaba but is not for jr/multiplex) you will waste a lot of memory even for unused channels as c9x will change on all 32 taranis channels. Changing radio means to re...

Ok I did the tts_es file so i suppose to know how is done :) 0...100 as numbered with 100=cien 101=ciento 102=doscientos 103=tercientos 104=cuatrocientos 105=cinquecintos 106=sescientos 107=setecientos 108=ochocientos 109=nuevecientos 110=mil 111=virgola 112=UN, 113=UNA, 114=Y, 115=MENO, 116=HORA, 1...

Thanks for highlighting....

you probably have a 9xr radio with M128 and you are trying to use as a normal 9xr with M64.

There are some sound for spanish and they should be ok ?
where did you downloaded them from ?
Which firmware release do you have on your sky9x board
If it's the latest did you selected spanish in general settings ?

receiver match actually works only with x8r receivers.

/usr/local/bin/avrdude ?? for sky9x ??? It should be sam-ba not avrdude !!! It cannot work with arm processors as avrdude is done for atmega series one... Unluckily SAM-BA does not exist on MacOSX, so sky9x board cannot be supported at the moment. We will drop the support on Mac until a solution wil...

A typo in the script: CHIOCE instead of CHOICE as parameter
but that's me, a little bit dyslexic

try to redownload ..
i suppose to have found the reason

well companion on mac (as in all other OS) just calls avrdude for performing the write/read operation:
so I presume it's avrdude or a programmer driver issue.

which version of avrdude are you running ?

Which programmer are you using ?

Maybe only need a slowdown by adding the -B parameter

Do not consider c9x simulator: it does not actually runs the firmware you have downloaded but a static compiled version. First in general menu FAI choice must be present other way it means you have not downloaded the proper firmware. If you enable FAI Mode on the radio to disable you must edit the r...

try to reflash the radio again...
or eventually to slow down writing by adding a -B 50 in the advanced parameters

Sorry to bang on about this. Using the latest version of Companion and OpenTx for the M128 with the firmware ticked before downloading the firmware, the problem still persists. Companion shows in the Telemetry screen (on each model) using the Frsky sensor hub, the units show a 'Imperial' in grey. O...

What is really very strange is that 1.39 and 1.41 have been compiled by the same guy...

It as ben fixed, but please next time report as an issue in googlecode project's page.
Following five forum to get bugs reports has become impossible...

I suppose as the compilation machine changed, now is a mountan lion....
We are still trying to sort out...

Go on the field short click on [Enter] to enter in the edit mode and then [Enter long]

1) have a look in Flight Modes tabs... gvars are there

2) it should work if you set the sd structure path in the preferences.

you need to install version 0.97 and then overwrite with version 1.40

And please do not crosspost...

Anyway now companion9x has an automatic log session recognition in the log viewer

Helle you cannot open the file,
you need to do a restore from backup in a new memory.

I still do not consider it so good as makes much more complex the analysis of a single flight with multiple log start and stop during the flight. (you need to merge them)
Also populates SD fat with a lot of files.
Files are in CSV format:
Just open with your favorite spread sheet and cut the file.

Scott there is some issue we are trying to solve with Taranis...
The restore from backup function was implemented before the taranis was even in production
Helle is not wrong.

Please download the latest 1.39, not the one called "beta"

Are you sure it's not beeping due to RSSI alarms ?