Search found 1488 matches

by Daedalus66
Wed Jul 29, 2020 4:23 am
Forum: er9x
Topic: Solved, Flysky TH9X and Banggood 4 in 1 Module won't bind to Spektrum receiver
Replies: 17
Views: 13480

Re: Flysky TH9X and Banggood 4 in 1 Module won't bind to Spektrum receiver

Sorry, I’ve been tied up today. Will get back to this tomorrow.
by Daedalus66
Tue Jul 28, 2020 3:51 pm
Forum: er9x
Topic: Solved, Flysky TH9X and Banggood 4 in 1 Module won't bind to Spektrum receiver
Replies: 17
Views: 13480

Re: Flysky TH9X and Banggood 4 in 1 Module won't bind to Spektrum receiver

You said the Tx and module bound successfully with other models. What receivers are used in those models?
by Daedalus66
Tue Jul 28, 2020 3:47 pm
Forum: er9x
Topic: Solved, Flysky TH9X and Banggood 4 in 1 Module won't bind to Spektrum receiver
Replies: 17
Views: 13480

Re: Flysky TH9X and Banggood 4 in 1 Module won't bind to Spektrum receiver

Just had a thought. What model did the AR636A come from? It may make a difference since the AR636 will often only bind when placed in the same orientation as in the model for which it’s programmed. The key issue is which side down? In low wing models, it’s usually label down, while in high wing, its...
by Daedalus66
Tue Jul 28, 2020 3:16 pm
Forum: er9x
Topic: Solved, Flysky TH9X and Banggood 4 in 1 Module won't bind to Spektrum receiver
Replies: 17
Views: 13480

Re: Flysky TH9X and Banggood 4 in 1 Module won't bind to Spektrum receiver

Autobind is unlikely to help. It’s intended for protocols which bind automatically when the receiver is powered up. Channel order should not affect bind. What order are you using with the models that work with this Tc and module? I do have an AR636 to test with. What version of ER9X are you using? M...
by Daedalus66
Tue Jul 28, 2020 12:39 pm
Forum: er9x
Topic: Solved, Flysky TH9X and Banggood 4 in 1 Module won't bind to Spektrum receiver
Replies: 17
Views: 13480

Re: Flysky TH9X and Banggood 4 in 1 Module won't bind to Spektrum receiver

Hi Rod
I’ll have a go at your problem later today. I’ll have to dig out my old Turnigy 9XR, which is my last transmitter running ER9X (others have ERSkyTX).
Nigel
by Daedalus66
Sat Feb 08, 2020 10:15 pm
Forum: General help (FrSky Taranis radio)
Topic: Opentx for qx7 version 2.3.4
Replies: 6
Views: 6205

Re: Opentx for qx7 version 2.3.4

EU is European Union. EU regulations don’t allow D8.

EN is English.
by Daedalus66
Mon Nov 04, 2019 2:17 pm
Forum: openTx model setup
Topic: NOOB need help setting up Hobbyzone Sport Cub S
Replies: 62
Views: 84861

NOOB need help setting up Hobbyzone Sport Cub S

By the way, I’m not sure if it was clear that I’m recommending the website RCdiy.ca as one good source of instructions on programming OpenTX.

http://rcdiy.ca
by Daedalus66
Mon Oct 28, 2019 2:20 pm
Forum: openTx model setup
Topic: NOOB need help setting up Hobbyzone Sport Cub S
Replies: 62
Views: 84861

NOOB need help setting up Hobbyzone Sport Cub S

Hi Chubby Let’s try to get these two things sorted out. First, dual (and triple) rates and expo. These involve changing the way the control surfaces respond to stick inputs. Rates change the sensitivity across the whole range of movement while expo changes the shape of the response curve. Rates and ...
by Daedalus66
Sun Oct 27, 2019 2:24 pm
Forum: openTx model setup
Topic: NOOB need help setting up Hobbyzone Sport Cub S
Replies: 62
Views: 84861

NOOB need help setting up Hobbyzone Sport Cub S

Hello, I had a question regarding the d/r or t/r & expo on switch D. Would I use this as my emulation of the beginner/ intermediate/ experienced switch from original radio instead of the safe switch programmed on (channel 5 SA)? If so what is Switch A used for .... Outside of this I have succes...
by Daedalus66
Thu Oct 24, 2019 2:33 am
Forum: openTx model setup
Topic: NOOB need help setting up Hobbyzone Sport Cub S
Replies: 62
Views: 84861

NOOB need help setting up Hobbyzone Sport Cub S

Hello, I had a question regarding the d/r or t/r & expo on switch D. Would I use this as my emulation of the beginner/ intermediate/ experienced switch from original radio instead of the safe switch programmed on (channel 5 SA)? If so what is Switch A used for .... Outside of this I have succes...
by Daedalus66
Sat Oct 19, 2019 11:38 pm
Forum: openTx model setup
Topic: NOOB need help setting up Hobbyzone Sport Cub S
Replies: 62
Views: 84861

Re: NOOB need help setting up Hobbyzone Sport Cub S

You may need to adjust a few things for your Jumper. But basically it should be the same.
by Daedalus66
Sat Oct 19, 2019 12:02 am
Forum: openTx model setup
Topic: NOOB need help setting up Hobbyzone Sport Cub S
Replies: 62
Views: 84861

Re: NOOB need help setting up Hobbyzone Sport Cub S

Here are the promised pictures of the Inputs screen showing D/R and Expo (actually T/R).ImageImage
by Daedalus66
Fri Oct 18, 2019 2:30 am
Forum: openTx model setup
Topic: NOOB need help setting up Hobbyzone Sport Cub S
Replies: 62
Views: 84861

Re: NOOB need help setting up Hobbyzone Sport Cub S

Oops. Here are the pictures. https://uploads.tapatalk-cdn.com/20191018/c1bd2fde48f96b00e44d290d9069662d.jpg https://uploads.tapatalk-cdn.com/20191018/c7c9d0e8d8088273f3b316352e5a61f0.jpg https://uploads.tapatalk-cdn.com/20191018/155e8e95a1e8fa6194e2f8c6b9083c7a.jpg https://uploads.tapatalk-cdn.com/2...
by Daedalus66
Thu Oct 17, 2019 11:54 pm
Forum: openTx model setup
Topic: NOOB need help setting up Hobbyzone Sport Cub S
Replies: 62
Views: 84861

Re: NOOB need help setting up Hobbyzone Sport Cub S

Here’s what the Sport Cub S setup looks like on my Taranis QX7. It should be similar on your Jumper, except that the switch assignments may differ. I used Switch A for channel 5 (SAFE mode), Switch H (momentary) for Panic Recovery, and Switch F for Throttle Cut (invoked by Special Function). I haven...
by Daedalus66
Thu Oct 17, 2019 10:49 pm
Forum: openTx model setup
Topic: NOOB need help setting up Hobbyzone Sport Cub S
Replies: 62
Views: 84861

NOOB need help setting up Hobbyzone Sport Cub S

Sorry. I missed this when first posted. As indicated previously, Multiprotocol modules generally require that the transmitter be set up in AETR channel order. This means that if you use the wizard for setup you must answer the questions accordingly. Motor is on channel 3, while Aileron and Elevator ...
by Daedalus66
Fri Oct 04, 2019 3:45 am
Forum: openTx model setup
Topic: NOOB need help setting up Hobbyzone Sport Cub S
Replies: 62
Views: 84861

NOOB need help setting up Hobbyzone Sport Cub S

First, you are confusing limits with rates. The 80% referred to limits, set on what is now called the Outputs page. The other percentages are rates (as in D/R) and are set in the Inputs page. Second, and more important, you are reading something written four years ago. Since then the Multiprotocol f...
by Daedalus66
Thu Sep 05, 2019 12:52 am
Forum: openTx model setup
Topic: NOOB need help setting up Hobbyzone Sport Cub S
Replies: 62
Views: 84861

NOOB need help setting up Hobbyzone Sport Cub S

The rates and expo for three control surfaces (R, E, A) are controlled by the Rate switch on the transmitter (assuming you are using a DX4e, DX5e or DXe). The rates are 100% with the switch up (position 0) and approximately 70% with the switch down (position 1). On the MLPDSM, rates are controlled b...
by Daedalus66
Sun Sep 01, 2019 12:21 am
Forum: General help (FrSky Taranis radio)
Topic: X9-Lite not powering on
Replies: 4
Views: 6193

Re: X9-Lite not powering on

I put a blob of solder on the positive end of one battery. But you need a good hot iron of adequate size to make sure you can do it quickly without overheating the battery. There are two slightly different types of battery: flat top and button top. The X9-Lite requires button top if you are to avoid...
by Daedalus66
Sat Aug 31, 2019 8:55 pm
Forum: General help (FrSky Taranis radio)
Topic: X9-Lite not powering on
Replies: 4
Views: 6193

Re: X9-Lite not powering on

The plastic battery holders have sharp edges and tend to tear the plastic covering on the batteries during insertion or removal. I used very fine sandpaper to take the edges off mine.
by Daedalus66
Mon Aug 26, 2019 11:08 pm
Forum: General help (FrSky Taranis radio)
Topic: Taranis Q X7 shipped without microSD card slot??
Replies: 3
Views: 3713

Taranis Q X7 shipped without microSD card slot??

The slot is for a MicroSD, thus quite small. That’s the card partly popped out.
Image
Note that it’s called a “TF card” in the illustration in the manual.
by Daedalus66
Sun Aug 04, 2019 8:51 pm
Forum: General help (FrSky Taranis radio)
Topic: Problem binding X9 Lite with Bee Brain Lite
Replies: 7
Views: 7949

Re: Problem binding X9 Lite with Bee Brain Lite

When first released, the X9-Lite was NOT compatible with D16 (ACCST) but only with the new ACCESS protocol. It was necessary to flash to new tx firmware to get D16 compatibility. I suspect this is still the case for many units in the pipeline. Go to FrSky-R.C.com and download the 190605 update for X...
by Daedalus66
Mon Jul 29, 2019 10:42 am
Forum: openTx
Topic: First timer issues on QX7
Replies: 16
Views: 11656

First timer issues on QX7

That’s more like it!

Enjoy.

EDIT: I should add that if the Rx Channel Order in Radio Setup is correctly set to AETR, the Inputs page will show the channels in the same order. So the first line will read:

CH1: Ail I1 : Ail [etc.]

No confusion of channel numbering.
by Daedalus66
Sun Jul 28, 2019 11:53 pm
Forum: openTx
Topic: First timer issues on QX7
Replies: 16
Views: 11656

First timer issues on QX7

Bingo! I got my mix updated per the attached and it's working now! So basically in the mix, the first value should match the 'actual' channel order of the Rx which is TAER, but the 2nd part/column needs to show the order that the I-range apparently likes which is AETR. Very strange but Now I can ju...
by Daedalus66
Sun Jul 28, 2019 9:20 pm
Forum: openTx
Topic: First timer issues on QX7
Replies: 16
Views: 11656

First timer issues on QX7

The iRangeX and other Multiprotocol modules require the use of AETR as the standard channel order across all protocols. For DSM protocols, the module then translates to TAER order for transmission to the receiver. For your existing setup, you need to move the relevant mixes so they are associated wi...
by Daedalus66
Wed Jul 24, 2019 11:04 pm
Forum: Software
Topic: Flashing original software back on Tgy9XR
Replies: 8
Views: 6686

Re: Flashing original software back on Tgy9XR

Kilrah wrote:It's a 9XR. No card, no bootloader, just an AVR ISP connector...
Thanks for the correction.
by Daedalus66
Wed Jul 24, 2019 6:58 pm
Forum: Software
Topic: Flashing original software back on Tgy9XR
Replies: 8
Views: 6686

Re: Flashing original software back on Tgy9XR

Simply copy the file to the “Firmware” folder on the SD card. Then enter Bootloader mode by turning on the transmitter with the horizontal trims held together. Follow the menu to flash the firmware. It’s not obvious which version you are talking about. As I recall, the “original” firmware was r202 b...
by Daedalus66
Tue Jul 16, 2019 10:16 pm
Forum: openTx for FrSky radios
Topic: Model Artwork for Taranis
Replies: 519
Views: 1079573

Re: Model Artwork for Taranis

“Tarani” is better than “Taranis’s”, which is a singular possessive, as in “His Taranis’s screen was broken, so he couldn’t see the images at all.”
You could say “He had two Taranis transmitters.”
by Daedalus66
Tue Jul 16, 2019 3:08 am
Forum: Hardware
Topic: Multiple antenas
Replies: 4
Views: 4482

Re: Multiple antenas

It depends which is turned on for a given model. The point is just don’t ever disconnect either antenna if there’s any possibility that that RF unit might be turned on. In other words, the only time the external module’s antenna should be disconnected is when the module is removed, and the internal ...
by Daedalus66
Tue Jul 16, 2019 12:37 am
Forum: Hardware
Topic: Multiple antenas
Replies: 4
Views: 4482

Re: Multiple antenas

Never run a transmitter or module with the antenna disconnected! It will damage the output transistor.
by Daedalus66
Sun Jul 14, 2019 9:51 pm
Forum: openTx for FrSky radios
Topic: Model Artwork for Taranis
Replies: 519
Views: 1079573

Model Artwork for Taranis

The X9D for example has a significantly wider screen and higher resolution than the QX7. So the former can display these images while the latter can’t.

Opinion seems to differ on the plural of “Taranis”. :)

Go to advanced search