Search found 1351 matches

by Daedalus66
Sun Feb 04, 2018 8:40 pm
Forum: ersky9xr
Topic: Throttle stick reversed on one Tx
Replies: 4
Views: 119

Re: Throttle stick reversed on one Tx

Earlier versions of the firmware did not have the Hardware menu locked. It was precisely because people would change settings they didn’t understand, and that only needed to be changed rarely, that the lock was introduced. If you had the transmitter on an earlier version you might well have reversed...
by Daedalus66
Sun Feb 04, 2018 8:33 pm
Forum: er9x
Topic: Er9x test versions
Replies: 14
Views: 23211

Re: Er9x test versions

Phil
Mike has asked you repeatedly NOT to use this thread for discussion.



Sent from my iPhone using Tapatalk
by Daedalus66
Sun Jan 28, 2018 7:38 pm
Forum: er9x
Topic: The new Turnigy 9X hardware can use ER9X ?
Replies: 35
Views: 1518

Re: The new Turnigy 9X hardware can use ER9X ?

PCM is an obsolete protocol for FM radios. Ignore it.
by Daedalus66
Thu Jan 25, 2018 1:45 pm
Forum: FrSky Taranis radio
Topic: Internal and External module to same Rx
Replies: 4
Views: 101

Re: Internal and External module to same Rx

Each module has a unique ID number. A receiver can bind to only one ID number at a time. Hence a receiver cannot be bound to two modules.
by Daedalus66
Wed Jan 17, 2018 2:14 am
Forum: openTx
Topic: OpenTX 2.0.0
Replies: 297
Views: 41409

Re: OpenTX 2.0.0

Your second question was whether it was worth upgrading. Kilrah gave a very clear answer which amounted to:
1. The release posts on OpenTX website state what upgrading gets you.
2. Only you can decide whether the changes are worthwhile in your situation.
by Daedalus66
Tue Jan 09, 2018 2:23 am
Forum: ersky9x
Topic: Lemon Telemetry with ErSky9x
Replies: 2
Views: 89

Re: Lemon Telemetry with ErSky9x

Reserved for further details on Lemon telemetry.
by Daedalus66
Tue Jan 09, 2018 2:22 am
Forum: ersky9x
Topic: Lemon Telemetry with ErSky9x
Replies: 2
Views: 89

Re: Lemon Telemetry with ErSky9x

Reserved for screen shots of Lemon telemetry.
by Daedalus66
Tue Jan 09, 2018 2:21 am
Forum: ersky9x
Topic: Lemon Telemetry with ErSky9x
Replies: 2
Views: 89

Lemon Telemetry with ErSky9x

The purpose of this thread is to provide a place to discuss the use of ErSky9x with Lemon RX telemetry. Lemon telemetry uses DSMX/DSM2 and the Spektrum telemetry protocol. It is designed to work with current generation telemetry-enabled Spektrum transmitters such as the DX6, DX8G2, DX9 or DX18G2 (an...
by Daedalus66
Fri Jan 05, 2018 8:53 pm
Forum: General help (FrSky Taranis radio)
Topic: Taranis X9D+ channels are all wrong on the Rx
Replies: 7
Views: 181

Re: Taranis X9D+ channels are all wrong on the Rx

It’s not too difficult to move mixes using the transmitter. Just go to a line, press Ent to select it, then use the Move command to move it where you want. And so on for the required rearrangement. Not quick, but easy enough.
by Daedalus66
Thu Jan 04, 2018 2:53 pm
Forum: General help (FrSky Taranis radio)
Topic: Taranis X9D+ channels are all wrong on the Rx
Replies: 7
Views: 181

Re: Taranis X9D+ channels are all wrong on the Rx

Stick Mode and Default Channel Order must be set separately. Channel Order only applies to NEW models, it does not affect existing models.
Check that both are set correctly and create a new test model. I think you’ll find all works correctly.
by Daedalus66
Wed Jan 03, 2018 1:25 pm
Forum: Software
Topic: Copy multiple lines from one model to another using Companion?
Replies: 2
Views: 80

Re: Copy multiple lines from one model to another using Companion?

You can always duplicate an existing model and use the copy as the basis for programming the new build.
by Daedalus66
Mon Dec 25, 2017 8:25 pm
Forum: ersky9x
Topic: Help Exporting Model from OpenTx into ersky9x
Replies: 28
Views: 529

Re: Help Exporting Model from OpenTx into ersky9x

Thanks. Been a while since I used eepm.
by Daedalus66
Mon Dec 25, 2017 6:36 pm
Forum: ersky9x
Topic: Help Exporting Model from OpenTx into ersky9x
Replies: 28
Views: 529

Re: Help Exporting Model from OpenTx into ersky9x

I can’t get Reinhard’s file to open either.
by Daedalus66
Sun Dec 24, 2017 6:46 pm
Forum: ersky9x
Topic: Help Exporting Model from OpenTx into ersky9x
Replies: 28
Views: 529

Help Exporting Model from OpenTx into ersky9x

I took a look at the setup. I very much recommend that you stay with one of the two common stick modes, 1 (throttle on right) or 2 (throttle on left). It will simplify life! Also, there is no such thing as stick Order. Stick Mode describes which stick axis does what and has nothing to do with order....
by Daedalus66
Sun Dec 24, 2017 6:09 pm
Forum: ersky9x
Topic: Help Exporting Model from OpenTx into ersky9x
Replies: 28
Views: 529

Re: Help Exporting Model from OpenTx into ersky9x

Assuming you have mixes set at 100, you should see 100% throw on the channels (unless there are other mixes). Did you calibrate the sticks? Go to Radio Setup, Calibrate and follow the instructions. Almost everything you are asking is covered in the ER9X manual, recommended by João. Will look at the ...
by Daedalus66
Sat Dec 23, 2017 11:46 pm
Forum: The Pickled Gnu (The Pub)
Topic: Need Help- Maiden Phoenix 2000 Glider Flight - Bad Crash
Replies: 10
Views: 268

Need Help- Maiden Phoenix 2000 Glider Flight - Bad Crash

I’m an instructor in our club flight school. Even young pilots (who typically learn much faster than adults — especially the 50+ ones) need a few flights on the buddy box if they are not to crash on the first flight. I strongly recommend getting help by joining a club. That said, I have to admit tha...
by Daedalus66
Sat Dec 23, 2017 4:55 pm
Forum: The Pickled Gnu (The Pub)
Topic: Need Help- Maiden Phoenix 2000 Glider Flight - Bad Crash
Replies: 10
Views: 268

Re: Need Help- Maiden Phoenix 2000 Glider Flight - Bad Crash

Very sorry to hear about the crash. Just how much flying experience do you have? The Phoenix 2000 is not a good place to start if you are trying to teach yourself to fly. It’s not particularly hard to fly but it is slow to respond and has little or no self-righting tendency. Finally, as you have fou...
by Daedalus66
Sat Dec 23, 2017 1:53 pm
Forum: ersky9x
Topic: Help Exporting Model from OpenTx into ersky9x
Replies: 28
Views: 529

Help Exporting Model from OpenTx into ersky9x

That sounds plausible. The lesson is to take Channel Order and Stick Mode functions absolutely literally. The names say what they do. They must not be used otherwise or nothing you do will make sense. The other common mistake is not to realize that Channel Order affects only NEW models. It does not ...
by Daedalus66
Sat Dec 23, 2017 1:44 pm
Forum: RF MODULES
Topic: Orange Module running MULTI protocol
Replies: 570
Views: 48404

Re: Orange Module running MULTI protocol

Duh. Why couldn’t I find that? Thanks very much.
by Daedalus66
Sat Dec 23, 2017 4:33 am
Forum: ersky9x
Topic: Help Exporting Model from OpenTx into ersky9x
Replies: 28
Views: 529

Re: Help Exporting Model from OpenTx into ersky9x

Also I have my flaps on CH2 and CH3 but for some reason when in break/landing mode they are operated by the elevator stick, but in OpenTx version of the model they are controlled by the throttle stick with a deadpoint in the middle, any ideas where I am going wrong Thanks John You've got the wrong ...
by Daedalus66
Sat Dec 23, 2017 4:21 am
Forum: ersky9x
Topic: Help Exporting Model from OpenTx into ersky9x
Replies: 28
Views: 529

Re: Help Exporting Model from OpenTx into ersky9x

Hi Daedalus66 Ok think I have most of it setup correctly, one thing I have noticed which I cannot find out how to do is get the flight mode names to show on the 9XR Pro. I have attached a .rar file which has model setups in OpenTx and ersky9x. Please look at model P2K Test If running with OpenTx an...
by Daedalus66
Sat Dec 23, 2017 4:07 am
Forum: ersky9x
Topic: Help Exporting Model from OpenTx into ersky9x
Replies: 28
Views: 529

Re: Help Exporting Model from OpenTx into ersky9x

Same here. Just get error messages.
by Daedalus66
Fri Dec 22, 2017 5:20 pm
Forum: RF MODULES
Topic: Orange Module running MULTI protocol
Replies: 570
Views: 48404

Orange Module running MULTI protocol

Could you provide a link please. A brief search didn’t turn it up.
by Daedalus66
Fri Dec 22, 2017 4:42 pm
Forum: ersky9x
Topic: Help Exporting Model from OpenTx into ersky9x
Replies: 28
Views: 529

Help Exporting Model from OpenTx into ersky9x

The translation from OpenTX to ErSky9x is generally fairly straightforward, as, while no longer directly compatible, they stem from the same root and thus share the same logical approach. First make sure you are familiar with the basics of ErSky9x, then rebuild the OpenTX model step-by-step. Feel fr...
by Daedalus66
Thu Dec 21, 2017 10:15 pm
Forum: openTx
Topic: Mixing question for gliders
Replies: 28
Views: 3117

Mixing question for gliders

Please keep related questions one thread.
by Daedalus66
Thu Dec 21, 2017 10:12 pm
Forum: Template Library
Topic: SkySurfer with flaps setup?
Replies: 22
Views: 2830

Re: SkySurfer with flaps setup?

Open9x is quite old. Back then, there was no Inputs screen (as is still the case for ErSky9x). As for outputs, it has changed names in OpenTX from Limits, to Outputs to Servos, if I recall correctly. In ErSky9x it’s called Limits. I suggest you simply focus on either OpenTX or ErSky9x and learn how ...
by Daedalus66
Wed Dec 20, 2017 10:06 pm
Forum: The FRSKY Forum
Topic: D8R-II Plus Internal Voltage and 9XR Pro
Replies: 41
Views: 473

D8R-II Plus Internal Voltage and 9XR Pro

That’s a solution if you want to measure individual cell voltages. If you just want the total voltage of the battery it’s extremely simple and cheap to implement:
https://www.frsky-rc.com/wp-content/upl ... l/FBVS.pdf
Or make your own with a pair of resistors .
by Daedalus66
Wed Dec 20, 2017 6:12 pm
Forum: The FRSKY Forum
Topic: D8R-II Plus Internal Voltage and 9XR Pro
Replies: 41
Views: 473

Re: D8R-II Plus Internal Voltage and 9XR Pro

The 5v is the receiver voltage, provided by the BEC in the ESC. You want to know the flight pack voltage (11.1-12.6). To get this you have to use a sensor (simple voltage divider to reduce voltage to under 3v).


Sent from my iPhone using Tapatalk
by Daedalus66
Mon Dec 18, 2017 4:19 am
Forum: ersky9x
Topic: [SOLVED]How to install ERSky9x on Q X7 and update bootloader
Replies: 54
Views: 1951

[SOLVED]How to install ERSky9x on Q X7 and update bootloader

The templates are working on my QX7 with pf7r221 firmware, but only with the menu button, as Mike says.
by Daedalus66
Sat Dec 16, 2017 4:26 am
Forum: FrSky Taranis radio
Topic: Qx7 for RC tanks.
Replies: 4
Views: 204

Re: Qx7 for RC tanks.

I read your post. You still have to take the time to learn OpenTX. We were all new once.

Go to advanced search