Search found 13 matches
- Mon Mar 23, 2015 2:02 pm
- Forum: FrSky Taranis radio
- Topic: S.port/Telemetry Problem
- Replies: 3
- Views: 2739
Re: S.port/Telemetry Problem
You are absolutely correct even though i set the id from 1 to 5 the vario still messed up but when i set the id to 10 on the vario it all works, still strange thou because i did set all the id different when i put them on :/ but it works now so thanks
- Sun Mar 22, 2015 8:10 pm
- Forum: FrSky Taranis radio
- Topic: S.port/Telemetry Problem
- Replies: 3
- Views: 2739
S.port/Telemetry Problem
Ok i have and High Precision variometer, Gps, voltage, rpm/temp, amp sensor all daisy chained, but whenever i turn on it all on i do not recive telemetry, i have to disconnect some of it, then i recive voltage sensor and then i can connect the rest, it all got its own id from 1 to 5 so whats the pro...
- Sun Mar 01, 2015 7:21 pm
- Forum: er9x / gruvin9x / th9 based firmwares
- Topic: Using Trn Swith to turn P3 on
- Replies: 5
- Views: 12926
Re: Using Trn Swith to turn P3 on
awsome thanks man, i just set the switches in for l4 and l5 inside the P3 in their respective channels
but i did have to move my alarms down to figure it out i could use L6 to control pitch on my gimbal
Youtube video of it working
but i did have to move my alarms down to figure it out i could use L6 to control pitch on my gimbal
Youtube video of it working
- Sun Mar 01, 2015 5:43 pm
- Forum: er9x / gruvin9x / th9 based firmwares
- Topic: Using Trn Swith to turn P3 on
- Replies: 5
- Views: 12926
Using Trn Swith to turn P3 on
ok i want to use my trn swith to turn on P3 For my gimbal for Roll and when i press it again to use P3 to control Yaw and press again to turn off it starts with off klik it one time activate p3 to control roll klik 2 times to activate p3 to control Yaw klik 3 times to turn off, or something like tha...
- Sat Feb 21, 2015 11:06 pm
- Forum: er9x
- Topic: XJT Module and 9x
- Replies: 11
- Views: 7253
Re: XJT Module and 9x
ok i must try that
but can i then use both the internel screen and the s.port dashboard, or can i only use one of them
edit:
yes i can, i just had to split the signal now it works,
that is awsome, thank you very much
but can i then use both the internel screen and the s.port dashboard, or can i only use one of them
edit:
yes i can, i just had to split the signal now it works,
that is awsome, thank you very much
- Sat Feb 21, 2015 2:22 pm
- Forum: FPV Projects
- Topic: help needed, with fpv camera gimbal/control
- Replies: 4
- Views: 9022
Re: help needed, with fpv camera gimbal/control
ok, but but it happens to other servos aswell, and i know they have worked before, just with a different setup on my old quad, but same reciver and and transmitter ill tray to if it helps with the radio further away
edit: it did not help with the radio further away
edit: it did not help with the radio further away
- Sat Feb 21, 2015 8:19 am
- Forum: FPV Projects
- Topic: help needed, with fpv camera gimbal/control
- Replies: 4
- Views: 9022
Re: help needed, with fpv camera gimbal/control
yes servos is connected direct to the x8r module on channel 9 and 10 channel 11 is landing gear, the naza is connected to the sbus port on the x8r and s.port is connected to a lipo monitor, The x8r is powered via the naza and so channel 1-8 goes to naza via sbus and 9-16 is the pysical pins on the x...
- Fri Feb 20, 2015 8:44 pm
- Forum: FPV Projects
- Topic: help needed, with fpv camera gimbal/control
- Replies: 4
- Views: 9022
help needed, with fpv camera gimbal/control
My problem is that my camera does not move smoothly, especially when i use my goggles it works even worse, when i use the knops its margantly better but not much i am using an turnigy 9x with an xjt module and x8r module, i have bound it i 16 channel mode, and using pxx protocol, i have tried the ot...
- Fri Feb 20, 2015 8:42 pm
- Forum: er9x
- Topic: XJT Module and 9x
- Replies: 11
- Views: 7253
Re: XJT Module and 9x
yes mikeB it is updated to the latest,
i found out that if i use ppm protocol i do recive RX info, but with pxx protocol i do not, thats the only differnece so far
i found out that if i use ppm protocol i do recive RX info, but with pxx protocol i do not, thats the only differnece so far
- Sun Feb 01, 2015 3:19 pm
- Forum: er9x
- Topic: XJT Module and 9x
- Replies: 11
- Views: 7253
Re: XJT Module and 9x
sorry have been busy, i think i bound it with 2 jumpers 1-2 and 3-4 on the x8r module and both of the swithes on the xjt module is set to off
- Sat Jan 17, 2015 6:40 pm
- Forum: er9x
- Topic: XJT Module and 9x
- Replies: 11
- Views: 7253
Re: XJT Module and 9x
my post has to be reviewed everytime i post so if it gets in the correct order this should be posted after the other post i posted
I forgot to tell you that i do not recive telemetry when i disconnect my SPort Dashboard, but i do get it on the dashboard when its connected
I forgot to tell you that i do not recive telemetry when i disconnect my SPort Dashboard, but i do get it on the dashboard when its connected
- Sat Jan 17, 2015 6:00 pm
- Forum: er9x
- Topic: XJT Module and 9x
- Replies: 11
- Views: 7253
Re: XJT Module and 9x
im running er9x-r816 i see now that there is a 817 out but shouldnt matter, yes i have set the value to on in the er9x i recive telemetry on my s.port dashboard, using the s.port connection on the xjt module, and connected rx/tx to the telemetrEZ but i dont know if i can use both at the same time, o...
- Sat Jan 17, 2015 1:09 pm
- Forum: er9x
- Topic: XJT Module and 9x
- Replies: 11
- Views: 7253
XJT Module and 9x
OK question i have used my xjt module with my x8r, and recently i got it to work with 16 channels using pxx protocol, 1-8 though the s.bus port to my naza and 9-16 through the rest of the pins on the reciver to landing gear and camera. Not using all of the pins yet hehe, i allso have smartiparts boa...