openrcforums

At least Galileo shows up in oXs_gps.cpp... Thanks for tip, I will check my configuration a will try to make some tests on weekend. EDIT 9.I. So short report from today`s testing: 1, I checked my OXS config and I have enabled Galileo in oXs_gps.cpp as it is above ( to be exact: in INAV I have BN-20...

Hi, guys. I bought Aggressor FPV plane and installed Matek`s F411WSE flight controller there. I`m going to learn something about setup & tuning of INAV, however I noticed an interesting thing: at today`s flying INAV was reporting up to 25 satellites. In INAV I have enabled also Galileo satellite...

In oXs_out_frsky.cpp, you can find this code (from line 1612) ... Great thanks, however I was not successful ... Without DS1820 reading to SPORT sychro I had sometimes "peaks" on SatNums caused by SPORT communication problem. With sychro I have peaks on Alt cased by OXS timing influenced ...

Michel, is it possible to identify, when SPORT packed was sent?
I need to synchronize OneWire communication with SPORT communication and this seems to me the way: start OneWire communication just after SPORT data were sent.
Thanks, Daniel.

Kilrah wrote: ↑Wed May 06, 2020 8:32 pm OpenTX expects to receive GPS speed in knots as that's what the FrSky protocol defines, so you shouldn't send in km/h.

OK, my fault, thanks

It is not a big job but I did it in this way in order to save space in memory? Currently it is already probably not possible to activate all options because the AVR328p chip is short on memory. OK, so let it be. I`m at around 35% used memory including DS1820 one wire files :roll: I do not understan...

OK, I will try it and will report the result...
When You will do next OXS upgrade, is it big job to modify the communication to use 16-bit array instead of 8-bit?

All ID's from FrSky are defined in file oXs_out_frsky.h e.g. #define A3_FIRST_ID 0x0900 #define A3_LAST_ID 0x090f #define A4_FIRST_ID 0x0910 #define A4_LAST_ID 0x091f Still I fo not directly use those "define". Yes, I tried to modify those definition and nothing happened. I use an array i...

@msterns:I made OXS with volt_1&2 send as A3 and A4 and it replaced A3&4 send by R8 RX. Where can I change A3& A4 ID in OXS, please?

Oh really? Then what about other companies solution then? Futaba, Spektrum, Graupner, Hitec, Jeti, etc? Don't they do the same? :o :shock: Yes. But I `m flying nor of them, I`m flying FrSky. I`ve said You before: They can do, whatever they want, they are commercial company, that`s their business. B...

... please all ask yourselves, whether you aren`t partly responsible to push FrSKy into the situation, where they are today. Who prepared the ground, that products can sprout up with un-competitive minimum investment and market price and cause unbalanced competitive situations? Many people - many o...

In my opinion, they can do what the hell they want with their protocols, it is THEIR stuff. but what i see is people that don't even OWN their products bashing them because the protocols will not work with their multiprotocol module. Do you find that fair? I don't. And do You think it`s fair to do ...

... I have nothing to do with Frsky, as I said ... João, I don`t believe You, all the time You are talking like the FrSky`s advocate :lol: I was flying FrSky since autumn 2010, when they released DJT module + first generation od D8R. And `till 2019 I was buying only original D8Rs, no clones. When X...

It should be possible but it is not reliable. No... :( Not working with only #define T1_SOURCE MS5611 in oXs_config_basic.h I tried to add #elif defined(T1_SOURCE) && ( T1_SOURCE == MS5611) p_measurements[16] = &oXs_MS5611.varioData.temperature ; idToReply |= 0x10 ; to oXs_out_frsky.cpp...

Guys, is it possible to use MS5611 as temperature source ...

#define T1_SOURCE MS5611

... in FrSky HUB/ SPORT protocol? It is an option in Jeti...

//#define TEMPERATURE_SOURCE NTC // select between MS5611 and NTC

..., will it work in FrSky too? Thanks.

I just put a new version of oXs on github. I added 2 options in oXs_config_advanced.h in order to fill TEST1 with number of sat and TEST2 with hdop. As asked, number of sat is increased by 100 when there is a GPS 3D fix (or higher). ... Good job, Your project has one big problem, has no donation li...

Carbo thanks. Do You use any keywords at Your changes to be found? One more question: Is there any flag of GPS 3D fix? It can be included in satnum: if 3D fix == 0 => satnum = satnum if 3D fix == 1 => satnum = 100 + satnum EDIT: OK, I found test1.value = GPS_numSat ; test1.available = true ; test2.v...

I don`t know, whether it was here, but just briefly tested this GPS: https://www.banggood.com/BN-200-Small-Size-M8030-Chipset-GPS-Module-Antenna-GPS-GLONASS-Dual-GNSS-Module-p-1281187.html?rmmds=myorder&cur_warehouse=CN It works, can run on 10Hz, first fix after received from BG < 3min, hot fix ...

I am not sure it should be possible to support this protocol with oXs. This protocol uses 115200 baud rate which is quite fast for oXs because oXs does not use the hardware UART to communicate with the Rx. It uses a sofware serial UART because some protocol like FRSKY uses an inverted signal (not s...

Not exactly... Some basic wiring: https://github.com/betaflight/betaflight/wiki/Single-wire-FlySky-(IBus)-telemetry Here is type definitions https://github.com/qba667/FlySkyI6/blob/master/source/source/ibustelemetry.h from this project: https://github.com/qba667/MAVLinkToIbus/tree/master/MAVLinkToIB...

Maybe naive question ( to mstrens): isn`t it possible to add FlySky iBus protocol to OXS project? I found some small projects for DIY sensor for FlySky ia6B/ ia10B receivers, but nothing so complex as OXS...

Hello, gyus, does somebody know, how to change default colors in Companion`s telemetry log charts? The third color ( yellow) is not very suitable for old man`s eyes, so I want to change it. But nor Mr. Google helps me. Thanks.

1) The GPS has two leds. One for power one for satellite fix. When GPS has a good fix, the green LED starts to blink. oXs does not send data via Smartport before GPS has a good fix OK, you have another type... 2) I would strongly advice NOT to buy the GPS I have. I realy think it's counterfeit/fake...

Questions to twincam1449: 1, How do you know, that your GPS fix position? I have two LEDs on GPS, green ( blue) blink when GPS send data to OXS ( 10x per second ), red blink when GPS fix position 1x per second. Until GPS has no fix, OXS doesn`t send data do RX. 2, can you give some photos of your ox...

OK, thanks.
I read oxs_config_description.h, but it`s not clear from it, whether A0 and A1 can be swapped. It`s better for wiring. Some photos from my yesterday`s build:

Guys, is it possible to use on A0 reference mid- supply 4k7 + 4k7 and on A1 input from MPXV7002DP with
#define ADS_MEASURE A0_TO_A1 , ADS_OFF , ADS_OFF , ADS_OFF
configuration?

OK, thanks a lot for Your response , I will try it. So as I understand it: 1, in Taranis I must setup precision & range for AxxY ( I was wrong before, on AccX I have Model_QID) so that I get 200km/h at 2V from ADS1115? 2, special handling of Acc values I noticed before :mrgreen: 3, oXs_ads1115.a...

Yes, of course I have #define AIRSPEED_SENSOR_USE MPXV7002 // select between NO_AIRSPEED , MS4525 , MPXV7002 I forgot it to write it here :-( Well, if I will comment AccX, speed will be send as what variable... ? In FrSky Hub protocol I see nothing for airspeed :-( And once more: the measurement ran...

Guys, can you help me, please, with MPXV7002DP? This is my config: oXs_config_basic.h: // ***** 2.1 - Frsky data ***** ... #define ACCY_SOURCE ADS_VOLT_1 // select between TEST_1, TEST_2, TEST_3, GLIDER_RATIO , SECONDS_SINCE_T0 ,AVERAGE_VSPEED_SINCE_TO , VOLT_1, VOLT_2, VOLT_3, VOLT_4, VOLT_5, VOLT_...

Thanks a lot for your response, by the time I found, how to download it. Yes, I know, that XOS support NTC sensors, but digital is digital
DS18B20 is not so expensive, I`m going to try it. Great thanks for all your work at OXS.