openrcforums

i figure it out it was the settings in my Tx .

I'm having a problem binding xjt to the x4r-sb now i purchased both the xjt module and x4r-sb Rx in the u.s.a now i didn't upgrade no firmware tried binding straight from package now i have a flysky fs-th9x up graded to 9xtreme/ersky9x i had the dht module in the tx and d4r-ii works fine binded with...

i'm having the same problem binding xjt to the x4r-sb now i purchased both the xjt module and x4r-sb Rx in the us now i didn't upgrade no firmware tried binding straight from pacage now i have a flysky fs-th9x up graded to 9xtreme /ersky9x i had the dht module in the tx and d4r-ii works fine now i w...

i have a feeling that it is the little red usb plug because i took the same usb cable and pluged it in my old er9x board and what do you know i hear the compueter sound fom pluging it in. thing is where do i get a new usb plug for the mainboard.

i checked it i acactualy unpluged and turned the cable around still no connection.

i'm having problem withe my computer USB drive the tx which is a flysky th9x/er9x upgraded with the 9x treme board first off when i put it in boot load mode the screen on the tx has [ BOOT LOADER V1.7 READY ] BELOW THAT HAS ERSKY9X9XT _rom.bin ersky9x_rom bin now when i put the USB in it stays the s...

thanks mike for trying to help. but no luck. i tried putting ctot in it shows up on screen but no voltage.i put this knew board in 9xtreme thinking i could get reading on tx i should have just left the er9x board in i had frsky hub hooked up to that worked fine this board is nothing but a headache.

HELLO i installed the 9xtreme board into my flysky th9x/er9x now ersky9x can anyone help me get flight pack voltage reading from my naze32. i have d4r-II Rx i have green wire coming out of rx pin on d4r-II GOING TO - MINUS TELEMETRY SIDE ON NAZE32 FCB . AND the Red wire from tx on the D4R-II to + si...

I thought the naze32 does that? I don't have one so I don't know.. João yes it dose i have some reading to do . i was wondering do you have the djt module i still get the constant beeping from the module i was just wondering if it suppose be like that. maybe it's a rssi signal. because none of my a...

Yes you get the transmitter voltage on the screen but that has nothing to do with the telemetry. So, lets take a problem at the time. What voltage from the model do you need to read? Also, above I posted a link to the er9x manual. It is a good idea to read it. ;) João What voltage from the model do...

it sounds like the beeping is coming from the djt . It looks like the DJT might have some alarms programmed. Did you program any of those yellow/red alarms under A1 or A2 in the telemetry menu? This should really be removed as it was used long time ago when the radio still didn't handle alarms. No ...

Well, if you want to read the LiFe battery you will need a voltage sensor on A2. A1 is reading the voltage at the receiver. What is beeping? The radio or the DJT module? João it sounds like the beeping is coming from the djt . i want to thankyou again your really helping me out. the life battery is...

Throttle alarm when the stick is at the bottom means you have to calibrate the sticks. Go to Radio Setup/Calibration, and follow the instructions.. I think you are receiving telemetry as it seems you are receiving RSSI and TSSI (RX and TX). You have to program the radio to receive the receiver volt...

hello i have a question if someone would be kind to help ive installed the extreme board i have the flysky th9x/er9x/ersky9x djtmodule d4r-II i hooked the black and white wire in the djt white in rx black in tx is that correct ? dothe 2 little switches need to be in the off position? whe i turn my t...

ok got it. top picture loads just like that one the bottom picture dose not. i have to go into my file explorer a click on disk drive E and my sd card is there with Voice Pack for Ersky9x16Khz i guess it 's the same thing just about. any how thanks and i was just wondering every time i use the usb e...

ok got it. top picture loads just like that one the bottom picture dose not. i have to go into my file explorer a click on disk drive E and my sd card is there with Voice Pack for Ersky9x16Khz i guess it 's the same thing just about. any how thanks and i was just wondering every time i use the usb e...

hello mike B. THANKS FOR TRYING TO HEP I APPRECAITe IT AND everybody else with input i tryed put the USB INTO THE TX i'm getting tones on the computer but i'm only getting on the screen it says 9xtreme and at the bottom left it reads r00.3 and when i go into eepske-eeprom and try to read memory from...

hi to all fellow hobbyist i installed my 9xtreme board to my flysky th9x/er9x i recently had the er9x smartieparts board in now i have the 9xtreme board i have a djt module in the back of the tx first off when i go into radio set up it says for ver mod 9xt verv.1946-mike date 26.08.2015 ersky9x r218...