openrcforums

Hi

What is the safe low and high voltage range to use on Sky9X 3 ?

IE is both safe a 2Cell Lithium pack

and a 3 Cell Lipo?

MikeB wrote:How many splines on the shaft altogether? I have noticed that some servos have an odd number, so rotating the servo arm 180 degrees may make it line up.

Mike.

This is true

Sent from my C6603 using Tapatalk

Answers above are correct. But also a cloud fly wing servos are mounted in such a way that they normally do work opposite directions with a y lead. Lots of people are flying these with 4 channel receivers.

Sent from my C6603 using Tapatalk

My simple flashing guide
http://www.rcgroups.com/forums/showthread.php?t=1866014

Sent from my C6603 using Tapatalk

Hi,
Does this board have any capability of measuring or testing if the internal battery is ok?

Sent from my C6603 using Tapatalk

Spoogy wrote:Hi,

5 pieces availabe at here Finland -> http://www.verticalhobby.com/kauppa/frs ... -2324.html

-Spoogy

Thanks will check it out and see if they will ship to me.

Sent from my C6603 using Tapatalk

Will programming this be possible? Currently I use a virtual switch time off 1s time on 0.1s to run Led strobes controlled by the radio. Ersky9x.
Any ideas how to program this at a specific pwm frequency?

Sent from my C6603 using Tapatalk

Still nobody?

Sent from my C6603 using Tapatalk

Very nice thanks for explaining again. This would free up a couple of channels on my FPV plane so I can actually use my pan tilt now.

Sent from my C6603 using Tapatalk

I may have missed the point here a little.
Why use a digital uplink? Why not use 6 different pwm levels on one channel? Is it so u can have any combination?

Will it be theoretically possible to have a telemetry uplink to replace data radios for flight controllers?

Sent from my C6603 using Tapatalk

OK, today this volume all of a sudden is reduced to minimum again. This happened while the Tx was on all the time and I was replacing the fly pack on the model and after the fly pack is replaced and connected, I turn one of my switch on and the voice announcement becomes very low (it was normal vol...

Hi
I cannot find the fuel guage sensor online anymore or at Hobbyking.
Does anybody know where and if if this is still available?

Thankyou

Sent from my C6603 using Tapatalk

Do you lose ALL sounds, beeps as well as voice? Mike. I loose all sounds. Has there been any solutions. This is now happening very often. I made a really stupid mistake last week rebooting the radio while the glider was in the air. I thought my fail safe was set to last position which would give me...

MikeB wrote:OK, problem found, fix on its way!

Mike.

Hi
Have these problems been fixed? regarding vario level silence and sink tone option?

I cant keep up, where do I download the R188 now?

What about using an android phone connected to the radio via Bluetooth? Can the phones accelerometers be used for inputs?

Sent from my C6603 using Tapatalk

I love how you always get an answer on this forum, unlike others that always tell you to do a search...

Sent from my C6603 using Tapatalk

I retested to make sure I didn't make a mistake. I have firmware 182 loaded. When I hold the receiver level I get a constant buzz tone. If I raise it I get the higher pitch solid tone. When I lower it I get the lower buzz tone. I have tried different sensitivities but I always have the in between bu...

Ok just bench tested Vario tones. Its working well. Just some question: With the A2 Source selected and the vario sensor only connected to the digital port on the RX it still works? (What is the preferred layout?) I can't select the Option to disable sink tones. The cursor keeps skipping it? Can we ...

You should find the option in the "TELEMETRY2" menu. It's right at the bottom. You choose a source, enabling switch, sensitivity and whether you want tones when sinking. Currently on the new FrSky vario sensor is supported, but the old one wasn't very good anyway. Mike. Aah there it is, t...

MikeB wrote:r180 committed.
Vario Sink Tones option reversed - makes it read more sensibly

Mike.

Hi

After reading this change log I assumed vario tones have been adding to the ERSKY firmware?
I cant find any options to make this work, am I missing something? Too much reading for me :/

Hi

Is there a step by step guide on how to get eepskye to communicate with my TX?

Hi Sorry for my ignorance Ive been trying to follow this, but still don't fully understand the excitement. What is the benefits of this PXX protocol? Apart from model matching, I assume this links models on the radio to specific receivers? I have a sky V3 board and a DJT, and a few D8R 2 receivers. ...

Thanks I am getting the warnings working, but how can I set them to repeat ?

Thanks

Is there an explanation somewhere of the usage of these formulas? " V<ofs "
Then I can do the other warnings myself

Scott Page wrote:

GTiDon wrote:Sometimes my sound dies, until I turn the radio off and on again.

Which firmware and version do you have. I know that was an issue with open9x - but thought they had stomped that but awhile ago.

I am using Ersky9X, updated to latest about 30 days ago

Hello

How do I set a voice alarm for A1 voltage below a certain level?

Sometimes my sound dies, until I turn the radio off and on again.

Is there a set of instructions anywhere indicating how to configure the application to communicate with a sky board?

Win 7 64 bit
With sky v3.0

Samba direct connects no problem but not from c9x

Sent from my LT15i using Tapatalk 2

Hi

I still cant get c9x to see my radio I get this. What must I do?