Cracked it, I had forgotten to setup the telemetry options, set now and the tx works smoothly, back to the pond later in the week to check it over!!
Again, thanks Mike, you're a life saver!!
Search found 238 matches
- Mon May 27, 2024 10:02 am
- Forum: ersky9xr
- Topic: 9XR Pro tx with Orange module, and Spectrum AR6100 rx
- Replies: 6
- Views: 419
- Sun May 26, 2024 11:22 am
- Forum: ersky9xr
- Topic: 9XR Pro tx with Orange module, and Spectrum AR6100 rx
- Replies: 6
- Views: 419
Re: 9XR Pro tx with Orange module, and Spectrum AR6100 rx
Ok, after thinking i had bound the system, at the pond it all fell apart, the boat mounted system when turned on(after the tx) started to hunt - the speed controller started up shut, down and it cycled like that. Tried rebinding, no change. so I abandonned the silliness. THe Pro protocols were playe...
- Thu May 23, 2024 5:56 pm
- Forum: ersky9xr
- Topic: 9XR Pro tx with Orange module, and Spectrum AR6100 rx
- Replies: 6
- Views: 419
Re: 9XR Pro tx with Orange module, and Spectrum AR6100 rx
Have just been playing around with the pieces -- and got it working, now to test it in a boat at the pond over the weekend.
Will give some feedback next week!
Thanks for pointing me Mike!
Tony S
Will give some feedback next week!
Thanks for pointing me Mike!
Tony S
- Wed May 22, 2024 7:09 am
- Forum: ersky9xr
- Topic: 9XR Pro tx with Orange module, and Spectrum AR6100 rx
- Replies: 6
- Views: 419
Re: 9XR Pro tx with Orange module, and Spectrum AR6100 rx
Hi people, egg on face time, I transposed the rx code, should be AR6100, should have checked before mounting on site.
Help still requested!!
Help still requested!!
- Tue May 21, 2024 6:06 pm
- Forum: ersky9xr
- Topic: 9XR Pro tx with Orange module, and Spectrum AR6100 rx
- Replies: 6
- Views: 419
9XR Pro tx with Orange module, and Spectrum AR6100 rx
I have a 9XR Pro tx flashed with ERSky etc works fine with Orange rx's. I have been given a couple of Spectrum AR1600 rx's. I am struggling to get them working, have tried various configurations all to no avail, can't get them to bind. Will they bind? How should the tx be set up to achieve this? I h...
- Tue Oct 31, 2023 3:51 pm
- Forum: er9x
- Topic: er9x on a modern tgy 9xhi all
- Replies: 0
- Views: 10566
er9x on a modern tgy 9xhi all
Hi all,
Can a modern tgy 9x transmitter be flashed with ER9x software, the system uses the Flysky 2a mode receivers?
I recall some time ago this question arose and a solution of changing polarity was made. Does this work, or are there any other tweaks to get the system and ER9X working?
TIA
Tony S
Can a modern tgy 9x transmitter be flashed with ER9x software, the system uses the Flysky 2a mode receivers?
I recall some time ago this question arose and a solution of changing polarity was made. Does this work, or are there any other tweaks to get the system and ER9X working?
TIA
Tony S
- Wed May 03, 2023 12:08 pm
- Forum: ersky9xr
- Topic: Exponential servo operation?
- Replies: 2
- Views: 1857
Re: Exponential servo operation?
Thanks for that Mike!
Looking like an interesting time next time I visit the club pond!
Cheers
Tony
Looking like an interesting time next time I visit the club pond!
Cheers
Tony
- Tue May 02, 2023 7:45 am
- Forum: ersky9xr
- Topic: Exponential servo operation?
- Replies: 2
- Views: 1857
Exponential servo operation?
Hi all,
Been looking around to see if there is a program within the 9XR Pro system to set up an exponential servo operation without plotting said curve in curves? ---- I want to try on the steering of a boat!
Thanks in advance
Been looking around to see if there is a program within the 9XR Pro system to set up an exponential servo operation without plotting said curve in curves? ---- I want to try on the steering of a boat!
Thanks in advance
- Sat Jan 07, 2023 2:34 pm
- Forum: Hardware
- Topic: Advice / clarification of setup ersky9x
- Replies: 4
- Views: 5849
Re: Advice / clarification of setup ersky9x
ok, have achieved an equilibrium with the two motors using the sub trim settings for both motors in the limits area.
I am now a happy bunny, thanks Mike.
I have added this to my little book of crib notes, again many thanks!
I am now a happy bunny, thanks Mike.
I have added this to my little book of crib notes, again many thanks!
- Sat Jan 07, 2023 12:15 pm
- Forum: Hardware
- Topic: Advice / clarification of setup ersky9x
- Replies: 4
- Views: 5849
Re: Advice / clarification of setup ersky9x
They are un named chinese pieces costing about 5 - 6€, 10amp with a 20 instantaneous, no central brake function, so straight from forward to reverse! The two motors, when both run with the same directional rotation start together in both directions. Because the motors are being run anti clockwise an...
- Fri Jan 06, 2023 7:42 pm
- Forum: Hardware
- Topic: Advice / clarification of setup ersky9x
- Replies: 4
- Views: 5849
Advice / clarification of setup ersky9x
Hi all Bloavez mad / Happy New Year one and all! The following might need moving to a more appropriate forum topic! I have been asked by a modelling colleague to set up his 9XR Pro to control a 2 motored boat. Fine, i have installed V tail mixing and have both motors working fine. I have a small pro...
- Wed Aug 31, 2022 9:48 am
- Forum: er9x / gruvin9x / th9 based firmwares
- Topic: Notes on programing
- Replies: 1
- Views: 4011
Notes on programing
Hi all
Is there a handbook that outlines the various functions and there uses?
I am a complete novice after programing the basic functions
Thanks in advance
Tony S
Is there a handbook that outlines the various functions and there uses?
I am a complete novice after programing the basic functions
Thanks in advance
Tony S
- Sun Aug 28, 2022 10:15 am
- Forum: er9x model setup
- Topic: Turnigy 9X running ER9X setup to run a tank, how?
- Replies: 10
- Views: 12110
Re: Turnigy 9X running ER9X setup to run a tank, how?
Hi all Finally got back to fiddling with tis, and using the link by ReSt and the setup suggested by pstimpel I have more or less what i want, the Tank rolls as expected, the only piece missing is the horiz left and right sticks do not generate anything for this situation, not a problem , the tank is...
- Wed Aug 24, 2022 10:03 am
- Forum: er9x model setup
- Topic: Turnigy 9X running ER9X setup to run a tank, how?
- Replies: 10
- Views: 12110
Re: Turnigy 9X running ER9X setup to run a tank, how?
Nope, didn't work, as above tracks rolling in opposite directions when in fwd and rev.
I'll knock up a test thingy later to test/check the programming, ie 2 x motors with tell tales on the shafts with a similar receiver etc!
I'll knock up a test thingy later to test/check the programming, ie 2 x motors with tell tales on the shafts with a similar receiver etc!
- Wed Aug 24, 2022 8:35 am
- Forum: er9x model setup
- Topic: Turnigy 9X running ER9X setup to run a tank, how?
- Replies: 10
- Views: 12110
Re: Turnigy 9X running ER9X setup to run a tank, how?
Tried that, didn't work, the left and right tracks were rolling in opposite directions!
- Wed Aug 24, 2022 6:09 am
- Forum: er9x model setup
- Topic: Turnigy 9X running ER9X setup to run a tank, how?
- Replies: 10
- Views: 12110
Re: Turnigy 9X running ER9X setup to run a tank, how?
You have listed 2 x CH1's, should the 2nd one be CH2?
I am just about to load the settings, and will use the 2nd CH! as CH2
I'll get back to you in due course!
I am just about to load the settings, and will use the 2nd CH! as CH2
I'll get back to you in due course!
- Tue Aug 23, 2022 3:57 pm
- Forum: er9x model setup
- Topic: Turnigy 9X running ER9X setup to run a tank, how?
- Replies: 10
- Views: 12110
Re: Turnigy 9X running ER9X setup to run a tank, how?
Thanks for the speedy reply, I think the latter situation would work best, the tank will be part of a demonstration piece with a landing craft and the disembarquation etc. I thought the V programming would have worked on the tank, it has been used on the landing craft without probs for some time! ag...
- Tue Aug 23, 2022 1:37 pm
- Forum: er9x model setup
- Topic: Turnigy 9X running ER9X setup to run a tank, how?
- Replies: 10
- Views: 12110
Turnigy 9X running ER9X setup to run a tank, how?
Hi all, As above, I am trying to set the tx to control a tank, have used the plane 'v' tail mix. Ok it is set up as follows Ch1 50% Rud + 50% Elev Ch2 50% Rud + -50% Elev For the most part it works fine, however when turning to the left with the stick in top left position ie going forwards, works fi...
- Fri Jun 10, 2022 10:00 am
- Forum: er9x
- Topic: download manual er9x
- Replies: 0
- Views: 2948
download manual er9x
Hi all
I want to download the above manual the system keeps falling over because of phishing stuff, how can i do it?
cheers
Tony
I want to download the above manual the system keeps falling over because of phishing stuff, how can i do it?
cheers
Tony
Re: XR Pro
no same, as before
i'll try remaking the ribbon cable joint feeding the screen later
i'll try remaking the ribbon cable joint feeding the screen later
Re: XR Pro
11.5v
tomorrow i will try a different sd card, if it works i'll reflash the system!
tomorrow i will try a different sd card, if it works i'll reflash the system!
Re: XR Pro
nope, nothing!
Re: XR Pro
ok, my error, missed the 9, its a
Tgy 9XR Pro
Hopefully I will get back to it either later today or tomorrow / or weekend!
Tgy 9XR Pro
Hopefully I will get back to it either later today or tomorrow / or weekend!
XR Pro
Ok, its been awhile!
I have an XRPro,just started to look at upgrading to Er9xsoftware,swithched on, power to indicator light,but no screen illumination, can anyone point me at postings etc on here, i recall some several years ago but cannot find them!
Thanks
I have an XRPro,just started to look at upgrading to Er9xsoftware,swithched on, power to indicator light,but no screen illumination, can anyone point me at postings etc on here, i recall some several years ago but cannot find them!
Thanks
- Sun May 02, 2021 3:10 pm
- Forum: Hardware
- Topic: 9XR Pro Screen not working on power up,
- Replies: 8
- Views: 5826
Re: 9XR Pro Screen not working on power up,
So, set up an rf module and an rx with servos connected tried the bind procedure, it bound, switched all off, removed bind loop, switched on, tx then rx -no led showing in rx.no servo movement Switch on pressing horiz bars, connect nothing and the voltage check, with the rf board mounted or on its o...
- Sun May 02, 2021 1:56 pm
- Forum: Hardware
- Topic: 9XR Pro Screen not working on power up,
- Replies: 8
- Views: 5826
Re: 9XR Pro Screen not working on power up,
Yes, getting continuity across it with a reading of 0.7 ohms - a jumper wire perhaps?
- Sun May 02, 2021 11:27 am
- Forum: Hardware
- Topic: 9XR Pro Screen not working on power up,
- Replies: 8
- Views: 5826
Re: 9XR Pro Screen not working on power up,
Ok, cleaned/remade all connections in the tx, still nothing, only the power on blue light, also with the tx connected to my laptop, it is not detected, any suggestions please?
- Wed Apr 28, 2021 12:51 pm
- Forum: Hardware
- Topic: 9XR Pro Screen not working on power up,
- Replies: 8
- Views: 5826
Re: 9XR Pro Screen not working on power up,
No , its not that, any other suggestions, later today I will clean all the plugs sockets and re make the screen connection etc
- Wed Apr 28, 2021 8:47 am
- Forum: Hardware
- Topic: 9XR Pro Screen not working on power up,
- Replies: 8
- Views: 5826
9XR Pro Screen not working on power up,
Hi all Been a while, lost/misplaced my notes, I have a Pro tx, powering on, the blue power light works but screen remains 'dead' I remember a fix for this(dead resistor of 0ohms I think, just needing a bridge) but cannot find the piece, any suggestions please, and finally mr dumb here asking, a stra...
- Sat Aug 15, 2020 1:00 pm
- Forum: Hardware
- Topic: CM621 6 ch rx dsm2 for dx6 etc
- Replies: 1
- Views: 3058
CM621 6 ch rx dsm2 for dx6 etc
Another quick question, got cm621 clone rx , using with a 9xr pro and orangerx dsm2/dsmx module setup in protocols as normal, it binds fine, then when bind cable removed and rebooted with a motor and servo's connected, all works fine for a couple of mins then the motor goes to full speed and the ser...