openrcforums

I wish to make a sincere apology to this forum for my mis-guided comments. I do understand the amount of work put in by people who volunteer to do this work on our behalf. My comments were said in haste with no thought for the feelings of these volunteers. As said in my previous comments, I have rec...

I was grateful for the reply from Mike B, and have been grateful for his help in the past. However maybe our interpretation of the feedback is different. It would appear that I may have over reacted to a lack of response but having read a number of unanswered posts on the forum, there is definitely ...

This forum page is for feedback, which I have given.
As I no longer have a usable taranis because of the inability of the forum to cater for the uninitiated in the complexities of opentx, perhaps you would kindly remove me from your forum!!

Thanks for the reply. It has explained in the main my concern.

Soco

As a keen Taranis owner and and an enthusiastic user of opentx, i am very disappointed that a request for assistance from myself has fallen on deaf ears or perhaps people consider it below them to answer what to them is probably a very simple solution. I would have thought that it is in the interest...

My apologies for the repeated topic

I would like to upgrade my Taranis plus with the latest firmware, however having read all the info regarding eu regulations and range issues etc. I am left confused, so seeking some un technical help. I have a taranis plus purchased mid 2015. Firmware is 2.0.15. Receivers I use are the D series and ...

Thanks Mike

Hi
I have just installed the latest companiontx (version 2.0.16). However when I try to simulate a model the program freezes and then closes.

Is this a fault with this version or am I doing something wrong?

Many thanks

Kilrah
Many thanks

soco

Hi again I inadvertently ticked the FAI box and then switched my taranis off, which meant that it then dissapeared from my transmitter. The instructions said that I needed to reset it from my PC using opentx companion. However have tried to do that but without success! Any help would be appreciated....

Jim
Thanks for that, the problem was just the length of the file names, so simple!

soco

Hi my taranis plus is running firmware open tx version 2.0.15 Need some custom sounds for 2 switches. I have produced these sounds as per video instructions. All the sounds are on my sd card, however when I try to use them on special functions menu the new sounds do not appear although the original ...

Hi again
Yes it would be far better if I had not tried to rush things and followed the video instructions properly! As you say Mike the menu is called inputs, and quite easy to understand.

soco

hi
As a follow on from my previous post, all instructions for dual rates and expo refer to the sticks menu, however that appears to be missing from the version I have.

Soco

Hi all
Just received my new Taranis plus. Have downloaded the latest Open TX firmware, version 2.0.15.
My first model I wanted to put some expo and dual rates on elevator a rudder but cannot find out how to proceed. Any help please.

Soco

Hi all
Have just opened eepe on my computer and it told me there was a new version etc. Decided to download it but unable to do so, after numerous attempts using different methods it appears I need a version for 64 bit windows.
Can anyone point me in the right direction for this file.

Many thanks

Joao

Just one simple final question, where can I find the latest firmware update?

Soco

Joao

With just a few very minor adjustments every thing is working perfectly.

I must give you my grateful thanks for your help and instruction.

Soco

Yes I only want spoilerons, what I have done on my transmitter is to use some offset to counter the flaperons.
Hope I have explain that ok

Joao short answer is yes it is my intention to add some differential, the file I sent you has only been done on epee, therefore is very basic. I have seen in the mix that as you say differential can be added through curve. Maybe what I should do is flash the model from my transmitter so that you can...

hope this is correct

Never posted a file here, do I just cut and paste it or is there another way?

Yes I did that part of the mix I did understand. There is still a small problem, the ailerons still operate until the stick goes past halfway, at that point they no longer operate. I assume its because the spoilerons (ailerons) are at their limit, is there a way of solving that?

Soco

Hi Joao

my apologies, I had it at +100% rather than -100%. It now works.

Many thanks for your help
Soco

Hi Joao

Tried as you suggested but unfortunately the motor ran at full revs when spileron was switches on.

Soco

Hi all
I have a turnigy 9xr using er9x firmware.
I am trying to get a mix that will be able to use my throttle stick to operate spoilerons without the motor also running,
Any help would be much appreciated.

Soco

Mike
Have just attached 4 separate servos and things seem ok, so I can only assume that one of the servos in the wings is faulty.
Hopefully I will now be able to work out how to get crow to work correctly. The videos by Richard Mrazek I have found to be very useful.

Soco

Mike Hope you can help with regards to previous posts about crow brakes. Although I thought I had sorted it out at the time I was only using one wing, therefore 2 servos. As soon as I have included connections to the other wing the sevos operate on their own jittering and moving in different directi...

Thanks Mike have sorted ir.

Many thanks

soco