Search found 16372 matches

by jhsa
Mon Feb 19, 2018 1:09 am
Forum: Software
Topic: Realistic driving in land vehicles.
Replies: 33
Views: 331

Re: Realistic driving in land vehicles.

It's the safety switch I used.. Please go to the "Model Setup / Safety Switches" and change the value from zero to 1 or 2. This should get you closer to the value you need.. Just increase further if necessary..

João
by jhsa
Sun Feb 18, 2018 9:23 pm
Forum: Software
Topic: Realistic driving in land vehicles.
Replies: 33
Views: 331

Re: Realistic driving in land vehicles.

Use the subtrim. Select channel 2. at top of the "LImits" screen you will see the selected channel value in micro seconds. Increase the subtrim until it reads 1525, simple :) The dead band is normal. Remember that normally you would be using the stick at it's middle position. Without the dead band, ...
by jhsa
Sun Feb 18, 2018 2:43 pm
Forum: Feedback
Topic: DDOS filtering
Replies: 19
Views: 489

Re: DDOS filtering

well, nothing we can do.. let's hope Rob fixes it soon..

João
by jhsa
Sun Feb 18, 2018 10:45 am
Forum: Software
Topic: Realistic driving in land vehicles.
Replies: 33
Views: 331

Re: Realistic driving in land vehicles.

Hmm, it looks like the electronics might be a bit offset and don't expect the zero to be zero.. if the electronics were designed for Futaba radios for example, the center point is not 1500uS (micro seconds) anymore, but around 1520uS. Try playing with the Sub-Trim value on the Thr channel in the "Mo...
by jhsa
Sun Feb 18, 2018 8:18 am
Forum: Hardware
Topic: TH9X/Turnigy 9x bricked after flashing
Replies: 18
Views: 196

Re: TH9X/Turnigy 9x bricked after flashing

Well done :) As I said, NEVER, EVER use the -F parameter..

João

Sent from my BLN-L21 using Tapatalk

by jhsa
Sun Feb 18, 2018 2:25 am
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 20
Views: 241

Re: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod

It is not a DDOS problem. If you haven't noticed yet, the filtering has been turned off for now. The files getting messed up seems to be a different problem..

João

Sent from my BLN-L21 using Tapatalk

by jhsa
Sun Feb 18, 2018 2:22 am
Forum: Feedback
Topic: DDOS filtering
Replies: 19
Views: 489

Re: DDOS filtering

Rob is looking into it..

João

Sent from my BLN-L21 using Tapatalk

by jhsa
Sat Feb 17, 2018 11:45 pm
Forum: Software
Topic: Realistic driving in land vehicles.
Replies: 33
Views: 331

Re: Realistic driving in land vehicles.

Good Luck :)

João
by jhsa
Sat Feb 17, 2018 9:13 pm
Forum: Software
Topic: Realistic driving in land vehicles.
Replies: 33
Views: 331

Re: Realistic driving in land vehicles.

The problem seems to be that you have had the radio configured wrong since the beginning.. As Mike said, if the throttle stick is on the left side, you should have mode 2 selected.. The reason you would have to fix all your models is because they might be all wrong :) If the throttle is zero, and th...
by jhsa
Sat Feb 17, 2018 1:38 pm
Forum: Software
Topic: Realistic driving in land vehicles.
Replies: 33
Views: 331

Re: Realistic driving in land vehicles.

This might not be the issue, but try calibrating the radio sticks and pots..

let me know if you need help with the weight and offset for new values.

joão
by jhsa
Sat Feb 17, 2018 1:19 pm
Forum: Software
Topic: Realistic driving in land vehicles.
Replies: 33
Views: 331

Re: Realistic driving in land vehicles.

Good :) then load again the latest model I posted and try it..

João
by jhsa
Sat Feb 17, 2018 1:06 pm
Forum: Software
Topic: Realistic driving in land vehicles.
Replies: 33
Views: 331

Re: Realistic driving in land vehicles.

I believe that you don't know how to configure the modes on your transmitter, and are just trying to play with the channel order to try to make things work. :( People often get confused about stick mode and channel order. they are NOT the same thing.. Please get the er9x manual from here http://open...
by jhsa
Sat Feb 17, 2018 12:17 pm
Forum: Software
Topic: Realistic driving in land vehicles.
Replies: 33
Views: 331

Re: Realistic driving in land vehicles.

I found a little problem as I didn't know, or didn't remember that you had changed the GEA switch to a 3 position switch.. Ok, TRH switch increases gears, and GEA- decreases gear now. I also changed the Throttle to Channel 2. if the model is not responding to the speeds you need, please look at the ...
by jhsa
Sat Feb 17, 2018 11:28 am
Forum: ersky9x
Topic: Test Topic
Replies: 0
Views: 37

Test Topic

Testing attaching files to the forum.. This topic will be deleted..

João
by jhsa
Sat Feb 17, 2018 10:40 am
Forum: Software
Topic: Realistic driving in land vehicles.
Replies: 33
Views: 331

Re: Realistic driving in land vehicles.

Will have a look later, but it did work in the eepskye simulator.. make sure you copied the settings correctly. Please do something.. post your eeprom here so I can compare and test it in eepskye. Perhaps some other setting is preventing it from working.. João EDIT: I read your post again, it looks ...
by jhsa
Sat Feb 17, 2018 10:34 am
Forum: openTx model setup
Topic: Using momentary switch to cycle through flight modes
Replies: 6
Views: 122

Re: Using momentary switch to cycle through flight modes

You could also increase a GVAR, and then reset it back to zero when it reaches a certain value. Detect the values with logical switches and assign them to control the flight modes.
Also to force the GVAR to zero use a logical switch.

João

Sent from my BLN-L21 using Tapatalk

by jhsa
Fri Feb 16, 2018 6:28 pm
Forum: Hardware
Topic: TH9X/Turnigy 9x bricked after flashing
Replies: 18
Views: 196

Re: TH9X/Turnigy 9x bricked after flashing

Can you please measure with a ohm meter if the resistors R2, R3 and R4 go to the programmer pins, and which ones?

João
by jhsa
Fri Feb 16, 2018 6:26 pm
Forum: Hardware
Topic: TH9X/Turnigy 9x bricked after flashing
Replies: 18
Views: 196

Re: TH9X/Turnigy 9x bricked after flashing

That should work if your radio is bricked, but we don't know that.. you could try though..

João
by jhsa
Fri Feb 16, 2018 3:04 pm
Forum: ersky9xr
Topic: RSSI
Replies: 4
Views: 77

Re: RSSI

Ersky9x can't be easier than OpenTX in everything.. Sometimes it must be less easy :) ;)
But for sure the "Scalers" are very powerful in other situations :) That is a small price to pay.. ;)

João
by jhsa
Fri Feb 16, 2018 1:13 pm
Forum: ersky9xr
Topic: RSSI
Replies: 4
Views: 77

Re: RSSI

by jhsa
Fri Feb 16, 2018 10:07 am
Forum: ersky9xr
Topic: RSSI
Replies: 4
Views: 77

Re: RSSI

Yes there is, Search the forum. I will also try to find it as soon as I can get ro a computer..

João

Sent from my BLN-L21 using Tapatalk

by jhsa
Fri Feb 16, 2018 12:20 am
Forum: Hardware
Topic: TH9X/Turnigy 9x bricked after flashing
Replies: 18
Views: 196

Re: TH9X/Turnigy 9x bricked after flashing

Also on your programmer, what are the values of R1, R2, R3 and R4?

João
by jhsa
Fri Feb 16, 2018 12:17 am
Forum: Hardware
Topic: TH9X/Turnigy 9x bricked after flashing
Replies: 18
Views: 196

Re: TH9X/Turnigy 9x bricked after flashing

you don't have a real m128 chip.. you have the compatible green chip that is known to have problems..

João
by jhsa
Thu Feb 15, 2018 9:57 pm
Forum: Hardware
Topic: TH9X/Turnigy 9x bricked after flashing
Replies: 18
Views: 196

Re: TH9X/Turnigy 9x bricked after flashing

Please confirm that all the connections between radio and programmer are good. Is the programmer permanently installed in the radio? is your programmer powering the radio's processor when programming, or are you turning the radio ON? A good picture of your radio mainboard and connections could help ...
by jhsa
Thu Feb 15, 2018 7:13 pm
Forum: Software
Topic: Realistic driving in land vehicles.
Replies: 33
Views: 331

Re: Realistic driving in land vehicles.

Here is a model file that you can load in eepskye and test.. This one use GVARs Adjusters, Logical switches and Safety switches... When ID^ is selected, the TRN switch increase the Gears, and the GEA switch decrease the gears. When you installed the pushbuttons, you will have to replace the TRN and ...
by jhsa
Thu Feb 15, 2018 6:39 pm
Forum: Hardware
Topic: TH9X/Turnigy 9x bricked after flashing
Replies: 18
Views: 196

Re: TH9X/Turnigy 9x bricked after flashing

try turning the THR and AIL switches ON and do another read.

João
by jhsa
Thu Feb 15, 2018 6:36 pm
Forum: Software
Topic: Realistic driving in land vehicles.
Replies: 33
Views: 331

Re: Realistic driving in land vehicles.

And i think i have 3 gears forward working for you.. Give half an hour or so.. will post a file for you to test. I am a bit concerned about your idea of not being able to drive from 0 on every gear.. But that is what I did and have working in eepskye at the moment. As i said will test further and po...
by jhsa
Thu Feb 15, 2018 5:29 pm
Forum: Hardware
Topic: TH9X/Turnigy 9x bricked after flashing
Replies: 18
Views: 196

Re: TH9X/Turnigy 9x bricked after flashing

some USBASP do need to be rebooted to be able to connect again, that is known. I know that this probably do not work, but what about if you try to read the eeprom instead of flashing the firmware?? You can also try to READ the fuses using companion.. you said you also mod the radio for telemetry? wh...
by jhsa
Thu Feb 15, 2018 1:36 pm
Forum: Hardware
Topic: TH9X/Turnigy 9x bricked after flashing
Replies: 18
Views: 196

Re: TH9X/Turnigy 9x bricked after flashing

welcome to the forum.. I aways used a usbasp v2.0, and -F parameter , but yesterday I got this issue. I believe that this was what possibly bricked your radio. You should NEVER EVER use the -F parameter.. Where did you read that you should use it?? :o :shock: We always advise people not to do it.. I...
by jhsa
Wed Feb 14, 2018 9:10 pm
Forum: Software
Topic: Realistic driving in land vehicles.
Replies: 33
Views: 331

Re: Realistic driving ind land vehicles.

It will work with momentary switches :D

João

Sent from my BLN-L21 using Tapatalk

Go to advanced search