Search found 1435 matches
- Thu Mar 09, 2023 9:40 am
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: OpenXSensor project page on google code
- Replies: 155
- Views: 187320
Re: OpenXSensor project page on google code
@Mike, you are probably right that GPS uses interrupts and that there is a risk of corrupted software serial. I never had complains on it. Probably it was not noticeable with a protocol like sport. About RPM, the code is in oXs_general.cpp and it uses an interrupt. See line ISR( TIMER1_CAPT_vect, IS...
- Sun Nov 22, 2020 9:25 pm
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: Multi rpm measure and synchronizing ..
- Replies: 5
- Views: 4644
Re: Multi rpm measure and synchronizing ..
Currently oXs can only measure 1 RPM.
I am not sure arduino is powerful enough to measure several RPM and to manage simultaneously different sensor + telemetry.
I am not sure arduino is powerful enough to measure several RPM and to manage simultaneously different sensor + telemetry.
- Sun Nov 22, 2020 8:22 am
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: oxs gps BN-220
- Replies: 10
- Views: 6866
Re: oxs gps BN-220
If your config declares that a mpu6050 is connected but the mpu is not connected, it can block oXs because there are some time out on the i2C bus.
Same issue exist with other I2C sensor (like MS5611).
This was perhaps the reason.
Same issue exist with other I2C sensor (like MS5611).
This was perhaps the reason.
- Sat Nov 21, 2020 9:42 pm
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: Need 30hz PWM out on a pin based on a channel input
- Replies: 2
- Views: 2989
Re: Need 30hz PWM out on a pin based on a channel input
Yes.
It is possible with an Arduino.
It is possible with an Arduino.
- Sat Nov 21, 2020 6:43 pm
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: oxs gps BN-220
- Replies: 10
- Views: 6866
Re: oxs gps BN-220
Note : to check if the Rx pin is defect, you have (with U-center) to send some commands to the GPS and not only listen to the data it sent. At start up, oXs sent some commands to the gps in order to activate some types of messages and to change the baudrate. It the Rx pin is defect, it could be that...
- Sat Nov 21, 2020 4:13 pm
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: oxs gps BN-220
- Replies: 10
- Views: 6866
Re: oxs gps BN-220
I do not expect that this is oXs related. It is probably an internal GPS issue.
Did you try to check your GPS using ublox u-center.
This freeware allows you to get and to display the data provided by the GPS
Did you try to check your GPS using ublox u-center.
This freeware allows you to get and to display the data provided by the GPS
- Fri Nov 20, 2020 11:00 pm
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: OxS Five temperature sensor and one voltage sensor
- Replies: 20
- Views: 10749
- Fri Nov 20, 2020 10:14 pm
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: OxS Five temperature sensor and one voltage sensor
- Replies: 20
- Views: 10749
Re: OxS Five temperature sensor and one voltage sensor
If you really want to get all temperatures (instead of min, index n and max), you can change some lines of code in file oXs_voltage.cpp You just have to remove the lines (from 271 up to 275) if ( numberOfNtc > 2) { voltageData.mVolt[FIRST_NTC_ON_VOLT_NR - 1].value = minTemp ; voltageData.mVolt[FIRS...
- Fri Nov 20, 2020 10:11 pm
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: OxS Five temperature sensor and one voltage sensor
- Replies: 20
- Views: 10749
Re: OxS Five temperature sensor and one voltage sensor
For 5 cylinder, you can get them with one single oXs (see my previous mail) For 7 cylinder, the easiest would be to use 2 oXs. In this case, you should have to change the device ID in the second one in order to avoid that both reply on the the same polling request from the RX. Othewise, in order to ...
- Fri Nov 20, 2020 9:59 pm
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: OxS Five temperature sensor and one voltage sensor
- Replies: 20
- Views: 10749
Re: OxS Five temperature sensor and one voltage sensor
If you really want to get all temperatures (instead of min, index n and max), you can change some lines of code in file oXs_voltage.cpp You just have to remove the lines (from 271 up to 275) if ( numberOfNtc > 2) { voltageData.mVolt[FIRST_NTC_ON_VOLT_NR - 1].value = minTemp ; voltageData.mVolt[FIRST...
- Fri Nov 20, 2020 9:42 pm
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: OxS Five temperature sensor and one voltage sensor
- Replies: 20
- Views: 10749
Re: OxS Five temperature sensor and one voltage sensor
in the line #define PIN_VOLTAGE 0 , 1 , 2 , 3 , 6 , 7 you declare which voltages have to be measured (here 6 voltage e.g) In the lines (e.g) define FIRST_NTC_ON_VOLT_NR 2 define LAST_NTC_ON_VOLT_NR 5 you declare which voltages have to be converted into degree. So here oXs will calculate degree based...
- Fri Nov 20, 2020 9:24 pm
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: Question about parsing the UBX sentence MSG_SOL and MSG_VELNED
- Replies: 4
- Views: 3687
Re: Question about parsing the UBX sentence MSG_SOL and MSG_VELNED
The kalman filter is used to calculate a vertical speed using the pressure sensor (converted in altitude) as wel as the vertical acceleration.
It is not foreseen for the velocity spikes.
It is not foreseen for the velocity spikes.
- Fri Nov 20, 2020 7:03 pm
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: OxS Five temperature sensor and one voltage sensor
- Replies: 20
- Views: 10749
Re: OxS Five temperature sensor and one voltage sensor
So, you can try to send some VOLT_x on ACCX, ACCY and/or ACCZ if those are not used for another purpose.
There is still an attention point using ACCX,Y. If remember wel, it requires using a scale (255?) on Tx side to get the expected value.
There is still an attention point using ACCX,Y. If remember wel, it requires using a scale (255?) on Tx side to get the expected value.
- Fri Nov 20, 2020 5:57 pm
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: OxS Five temperature sensor and one voltage sensor
- Replies: 20
- Views: 10749
Re: OxS Five temperature sensor and one voltage sensor
So, your arduino is not defect.
Perhaps, it is the Rx that does not accept that oXs uses the telemetry fields A3 or A4.
To check this, try to send VOLT_x (from Arduino pin A3) on another telemetry field (e.g. fuel source)
Perhaps, it is the Rx that does not accept that oXs uses the telemetry fields A3 or A4.
To check this, try to send VOLT_x (from Arduino pin A3) on another telemetry field (e.g. fuel source)
- Fri Nov 20, 2020 4:36 pm
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: OxS Five temperature sensor and one voltage sensor
- Replies: 20
- Views: 10749
Re: OxS Five temperature sensor and one voltage sensor
I do not see a conflict in your config files.
Do you get a value from A3 if you run another configuration (e.g. reading only A3 as volt_1 and sending it as VFAS)
Do you get a value from A3 if you run another configuration (e.g. reading only A3 as volt_1 and sending it as VFAS)
- Thu Nov 19, 2020 11:06 am
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: Question about parsing the UBX sentence MSG_SOL and MSG_VELNED
- Replies: 4
- Views: 3687
Re: Question about parsing the UBX sentence MSG_SOL and MSG_VELNED
Sorry but I do not know the answer.
- Wed Nov 18, 2020 12:06 pm
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: AFHDS-2A telemetry
- Replies: 1
- Views: 2140
Re: AFHDS-2A telemetry
I presume that AFHDS-2A is a Flysky receiver.
I do not know the FlySky receiver but I expect that it does not support the telemetry protocol from FRSKY, Multiplex or Jeti.
So I expect that it will not work with oXs
I do not know the FlySky receiver but I expect that it does not support the telemetry protocol from FRSKY, Multiplex or Jeti.
So I expect that it will not work with oXs
- Tue Nov 17, 2020 11:55 am
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: New beta version of openXsensor (=openXvario)
- Replies: 541
- Views: 313218
Re: New beta version of openXsensor (=openXvario)
In oXs_out_frsky.cpp, you can find this code (from line 1612) else // 8 bytes have been send { frskyStatus |= 1 << sensorIsr ; // set the bit relative to sensorIsr to say that a new data has to be loaded for sensorIsr. state = WAITING ; When the program enter this "else" section, it means ...
- Sat Nov 14, 2020 8:13 am
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: All-in-one sensor
- Replies: 2
- Views: 2603
Re: All-in-one sensor
I expect this can be done with oXs if the esc has a RPM signal. You can measure the total 6s voltage but if you also want to measure each individual cell, the accuracy will be limited. There is no need for programming. Just edit 2 configuration files. All explanations are given in the file oXs_confi...
- Tue Nov 10, 2020 4:05 pm
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: New version of oXs - Rf link quality
- Replies: 9
- Views: 6924
Re: New version of oXs - Rf link quality
I never tested with Frsky Hub protocol but it should normally work. I just checked the code and I did not find a reason why it should not work. I would have to debug the program to check. Note: I expect that the only change you made is activating the FRSKY_HUB (instead of FRSKY_SPORT). So, you still...
- Sun Nov 08, 2020 6:49 pm
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: New version of oXs - Rf link quality
- Replies: 9
- Views: 6924
- Tue Nov 03, 2020 12:44 pm
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: New version of oXs - Rf link quality
- Replies: 9
- Views: 6924
Re: New version of oXs - Rf link quality
Sorry but it is not possible to use S-Port to measure the link quality because it could be that s-port frames would be lost while frames used to drive the servos (PWM) would not be lost. The opposite is true too.
- Tue Nov 03, 2020 11:19 am
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: OpenXSensor project page on google code
- Replies: 155
- Views: 187320
Re: OpenXSensor project page on google code
Hi, Is there a way to build a simple 12S Sport voltage sensor ? that doesn't exist in FrSky range Do you want to get the voltage of each individual cell or only the voltage of the 12S. With oXs you can't get the voltage of each cell but it is easy to get the total voltage (just using a voltage divi...
- Thu Oct 29, 2020 12:03 pm
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: New version of oXs - Rf link quality
- Replies: 9
- Views: 6924
Re: New version of oXs - Rf link quality
The Rf link quality based on PWM needs an additional input on Arduino. It uses the arduino pin 2 or 3 (has to be defined as PIN_PPM). In fact the name PPM in oXs project is wrong. It would have been named PWM. So pin 2 or 3 has to be connected to a channel on the RX (just like a servo). All instruct...
- Tue Oct 27, 2020 10:22 am
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: New version of oXs - Rf link quality
- Replies: 9
- Views: 6924
New version of oXs - Rf link quality
I just put on github a new version of oXs (in Master branch). I added the possibility to measure the quality of the 2.4Ghz link between TX and RX. This requires to use a free PWM channel on the RX and to configure the TX in such a way that the signal on this channel changes continuously (e.g. using ...
- Sun Oct 18, 2020 9:09 am
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: RPM resolution?
- Replies: 232
- Views: 145741
Re: RPM resolution?
thanks for the feedback.
- Fri Oct 16, 2020 8:45 am
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: openxsensor locator
- Replies: 2
- Views: 2757
Re: openxsensor locator
In theory, it would be possible to send altitude but currently, this is not possible.
It was not the purpose of the locator.
It would request to rewrite part of the code (on both module - sender and receiver).
It was not the purpose of the locator.
It would request to rewrite part of the code (on both module - sender and receiver).
- Tue Oct 13, 2020 7:52 am
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: RPM resolution?
- Replies: 232
- Views: 145741
Re: RPM resolution?
You can try to filter the value on oXS side. In the .ino file you currently have sport_rpm.value = RpmValue ; Change it to //sport_rpm.value = RpmValue ; sport_rpm.value += 0.1 * ( RpmValue - sport_rpm.value ) ; You can then adapt the "0.1" parameter. With 0.1, it means that the new value ...
- Tue Sep 15, 2020 11:42 am
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: OpenXsensor and Frsky SxR Receivers
- Replies: 5
- Views: 4131
Re: OpenXsensor and Frsky SxR Receivers
I expect that there is another reason for the issue because oXs uses by default the following device Id's #define DATA_ID_VARIO 0x00 // = sensor 0 used for Alt and Vspeed #define DATA_ID_FLVSS 0xA1 // 1 used for Cell values #define DATA_ID_FAS 0x22 // 2 used for vfas , current and fuel #define DATA_...
- Tue Sep 15, 2020 10:16 am
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: OpenXsensor and Frsky SxR Receivers
- Replies: 5
- Views: 4131
Re: OpenXsensor and Frsky SxR Receivers
I have no experience with S8R but perhaps there is an incompatibility in the device ID being used.
oXs uses several devices ID's depending on the sensors being defined.
It is possible to change the devices ID's being used by oXs if this is would be the reason.
oXs uses several devices ID's depending on the sensors being defined.
It is possible to change the devices ID's being used by oXs if this is would be the reason.