Hi
I am a mac user but not having compiled anything before (don't know how to do it!) could you tell me whether there will be a later official release than the version on the site under downloads.
Regards
Dave
Search found 8 matches
- Tue Dec 09, 2014 1:45 pm
- Forum: openTx
- Topic: OpenTX Companion MacOS
- Replies: 7
- Views: 6913
- Wed Jun 04, 2014 7:16 am
- Forum: openTx
- Topic: OpenTX - Nightly builds for pre-2.0 testing
- Replies: 776
- Views: 446807
Version 2 Installation
Hi - Great job done by the team (at least I think its a team). I thought I should report a small issue with upgrading which some people (me) might get confused by. I was attempting to use 1.52 to upgrade the firmware only to find that 1.52 could not be used to locate version 2.0 of the Firmware. On ...
- Sun May 04, 2014 10:11 pm
- Forum: openTx
- Topic: OpenTX - Nightly builds for pre-2.0 testing
- Replies: 776
- Views: 446807
Re: OpenTX - Nightly builds for pre-2.0 testing
I thought I would try to contribute to the work of finalising version 2.0 but I have not been able to configure my Taranis to work with the new version. I write firmware to the TX and on restoring the transmitter reports bad eeprom etc and reformats it - I expected that. Trouble is I have not then b...
- Tue Jan 07, 2014 8:54 pm
- Forum: FrSky Taranis radio
- Topic: Ripmax Futaba FASST Module mix for Flying Wing
- Replies: 1
- Views: 2319
Ripmax Futaba FASST Module mix for Flying Wing
I am making slow progress with my Taranis but am getting there! I have just been trying to set up a flying wing mix (the template Delta is available) although on the Futaba TX this is called an Elevon mix. I can easily get the Frsky RX to work with this mix but for the life of me I cannot get the se...
- Mon Dec 30, 2013 11:07 pm
- Forum: FrSky Taranis radio
- Topic: Stuttering servo control with Futaba Module
- Replies: 4
- Views: 3605
Re: Stuttering servo control with Futaba Module
Finally managed to get to the field to try out your suggestion - weather has been dreadful. Works a treat. I obviously had the wrong value in the TX. Thanks
- Fri Dec 27, 2013 10:21 pm
- Forum: openTx for FrSky radios
- Topic: What values to set for telemetry?
- Replies: 7
- Views: 6741
Re: What values to set for telemetry?
I have been playing with the simpler voltage sensor with my Taranis connected to the balance plug n a 3 cell lipo and while it works fine there seems to be a difference between the voltage measured using a multimeter and that shown on the display. Is there a way of adjusting the displayed voltage to...
- Tue Dec 17, 2013 7:38 pm
- Forum: FrSky Taranis radio
- Topic: Stuttering servo control with Futaba Module
- Replies: 4
- Views: 3605
Re: Stuttering servo control with Futaba Module
Did you have the same experience?
- Tue Dec 17, 2013 7:06 pm
- Forum: FrSky Taranis radio
- Topic: Stuttering servo control with Futaba Module
- Replies: 4
- Views: 3605
Stuttering servo control with Futaba Module
I have been using my Taranis with a foamy before switching other models to it and I have run into an odd behaviour. As I have been a Futaba user I have plugged in an RM 12-MX Ripmax TX module bound to a Frsky FASST RX unit. The RX has been working fine on my 7C Futaba TX. The Taranis is set to PPM w...