Search found 11 matches
- Mon Oct 16, 2017 2:47 pm
- Forum: Hardware
- Topic: Taranis X9D Plus - Damage to mainboard/backboard?
- Replies: 39
- Views: 31506
Re: Taranis X9D Plus - Damage to mainboard/backboard?
Have you removed the connections you added for S3 and tried powering on then? Mike. Hi Mike, Sorry for the late answer. The problem has solved by itself. This very weekend I decided to give another look to the connections I soldered, and before even opening the case I unintentionally switched the T...
- Mon Oct 02, 2017 9:55 pm
- Forum: Hardware
- Topic: Taranis X9D Plus - Damage to mainboard/backboard?
- Replies: 39
- Views: 31506
Re: Taranis X9D Plus - Damage to mainboard/backboard?
Sorry if this is off topic. Today I installed a six position switch in my Taranis x9d plus as a new s3 pot. Everything looked fine, the switch worked ok, and I did the calibration. But, when I started configuring the Taranis, it just shut off in the middle of the process and now it won't turn on. I ...
- Mon Jul 28, 2014 7:51 pm
- Forum: Turnigy 9XR PRO radio
- Topic: FrSky FBVS-01 telemetry question
- Replies: 4
- Views: 4587
Re: FrSky FBVS-01 telemetry question
João, Thanks for your explanation! I gave it another try today. You are right, I set my alarms too high and under load they started too early and never stopped, unless I land my quad, so the voltage raised. It seems to me that my quad uses less current, so I will try with something like 10.8 for the...
- Mon Jul 28, 2014 4:44 pm
- Forum: Turnigy 9XR PRO radio
- Topic: FrSky FBVS-01 telemetry question
- Replies: 4
- Views: 4587
FrSky FBVS-01 telemetry question
Hi, Recently I have soldered my FBVS-01 voltage sensor to the + batery wire on the sensor side and cut the black one as I read in the docs. I resoldered the sensor side to 2S, as I have 3S LiPos and everything is fine. Then Murphy's law strike me, as it seems that it would be better if I soldered th...
- Thu Jul 10, 2014 6:46 pm
- Forum: ersky9xr
- Topic: How to transfer models from er9x
- Replies: 4
- Views: 4811
Re: How to transfer models from er9x
Just found out that there is a post by Mike about transferring models in Transmitter Hardware/9xr PRO.
Should have done my homework better before asking...
Should have done my homework better before asking...
- Thu Jul 10, 2014 6:11 pm
- Forum: ersky9xr
- Topic: How to transfer models from er9x
- Replies: 4
- Views: 4811
Re: How to transfer models from er9x
João,
You are right, that actually worked.
I could swear that I have tried it without success , must be growing old
Many thanks!
You are right, that actually worked.
I could swear that I have tried it without success , must be growing old
Many thanks!
- Thu Jul 10, 2014 3:12 pm
- Forum: ersky9xr
- Topic: How to transfer models from er9x
- Replies: 4
- Views: 4811
How to transfer models from er9x
Hi, I have a problem transfering my models from my old Turnigy 9x with er9x on it to 9xr PRO. Opening the .eepe file in eepSKYe doesn't do anything, and when I try to copy the moedl from eepe, it says it isn't supported. Even saving my models one by one, and loading them in 9xr pro, resulted only in...
- Thu Oct 10, 2013 11:23 am
- Forum: er9x
- Topic: er9x development
- Replies: 3179
- Views: 1461259
Re: er9x development
Mike,
It think I have the same problem like João with my HT8 which is connected to er9x thru the trainer/simulator port.
I have set the center beep on throttle but it beeps when the elevator is in center instead of throttle center.
Igor
It think I have the same problem like João with my HT8 which is connected to er9x thru the trainer/simulator port.
I have set the center beep on throttle but it beeps when the elevator is in center instead of throttle center.
Igor
- Mon Oct 07, 2013 6:51 am
- Forum: er9x
- Topic: er9x development
- Replies: 3179
- Views: 1461259
Re: er9x development
Hi Mike, I am using the FrSky version of the er9x. Here are two files, the one made with the old version of eepe with the old firmware, and the new one. In the new one I created a entirely new model for my new HiSky FBL100 which doesn't work. No data on the elevator channel at all. Don't know if I m...
- Sun Oct 06, 2013 12:07 pm
- Forum: er9x
- Topic: er9x development
- Replies: 3179
- Views: 1461259
Re: er9x development
Hi Mike, I also have problems with the new firmware, and really odd ones. I always do backups of my setup, so I did it this time also, but this time I forgot to backup the hex files as well as eepe, so I am stuck with the latest versions. Are there any previous version I can download? With the lates...
- Thu Sep 19, 2013 7:53 am
- Forum: er9x
- Topic: aleart thr ali switch warning
- Replies: 11
- Views: 5496
Re: aleart thr ali switch warning
Hi Bert,
This is normal for smartpie telemetry with older firmware. Just wait for about 15 secs and it will be gone, or press any key, or disable the alarms if You like.
The issue was resolved with the new firmware, so if You have a generic USBasp programmer, You can flash the TelemetryEZ.
Igor.
This is normal for smartpie telemetry with older firmware. Just wait for about 15 secs and it will be gone, or press any key, or disable the alarms if You like.
The issue was resolved with the new firmware, so if You have a generic USBasp programmer, You can flash the TelemetryEZ.
Igor.