openrcforums

Ah, of course! Thanks!
Markus

I don't get that, Reinhard. I think I have to test it with eepe to understand it... [emoji4]
Markus


Sent from my iPad using Tapatalk

Cool! Thank you very much!
Markus

Sent from my Q10 using Tapatalk

Hi, I have a problem with the following mix: CH3 +100% THR R -100% FULL Switch (TRN) Delay (u0:d2) Warn (3) Its purpose is obvious: If I pull the TRN switch longer than two seconds, throttle will go down to 0. It's a sort of safety switch with a delay. But the delay seems to work only one time, afte...

Thank you, Mike, for looking at this problem.

It's my first heli project with er9x, so I don't know exactly which are the right values.

Anyone else?

Markus


Sent from my iPad using Tapatalk

Hi, I do have a strange problem with my er9x (r812, Frsky version): In my new heli setup (120 swash plate) there are big differences between the channel behavior and the eepe simulation. Some examples as screenshot: https://plus.google.com/photos/104081931837928667051/albums/6040802162412985441?auth...

Hi, what does this "Update to Version 3" button do which I saw yesterday for the first time on the setup page in eePe?
All the best, Markus

Hi, does anybody know if this works with the jDrones IOBoard (http://www.jdrones.com/wiki/guide-jd-io ... vL2sX.dpbs)?
All the best, Markus

Hey guys, yesterday I updated my 9X from r810 to 811. Afterwards I had a strange problem: The calibration values of CH1 to CH3 had gone. And even worse: These three channels (AIL, ELE and THR) are now inverted in every single model setup. My update procedure was as always: Reading and saving the mem...

Okay, that doesn't sound very good. But nonetheless my Ctot value seems correct. I just connected a 4 cell battery and it showed 16.6 volts (same value as my voltmeter). Then I switched back to 3S and Ctot showed the correct voltage also. So it seems that Ctot is always okay, but V1...6 sometimes no...

In my setup the IOBoard just translates the Arducopter telemetry to the FrSky protocoll. Information about the IOBoard I use here and here . I don't use a FrSky LIPO sensor. I made a simple voltage divider for the APM which measures the voltage quite exactly. But that self built voltage divider does...

MikeB wrote:You have 4 cells showing, each of about 3 volts and a total of about 12 volts, looks correct to me! I would say that 3 volts for each cell is rather low.
Mike.

3 volts for each cell would be very low indeed, if there were 4 cells. But my battery is a healthy and full 3 cell lipo.
Markus

Hi, I am wondering why my radio shows cell voltage for 4 cells although my battery is only a 3 cell lipo. See photo below. My Setup: er9x, TelemetrEZ, D8R-XP, IOBoard. The total voltage is correct, as the second photo shows, only the cell voltage is wrong because "the system" (which part o...

Thanks, I'll try that. In the meantime, I need to find out if it is in deed no FrSky issue at all, but actually an APM issue. Because everything seems to work fine, if I connect servos to the receiver instead the APM. Strange....

Update: It was an connection problem, no FrSky or er9x problem!

What I'm saying is that with channel8 in the centre (1.5mS) all worked fine, but when you set channel 8 to something else (what exactly is the mix you have?), it goes wrong. Yes, it seems that's the problem. I attached a screenshot with my mixes. Are the 'BARS' on the tx screen showing the outputs ...

Could it be your frame length setting in er9x? What settings do you suggest? I use the default values (frame length: 22,5 mSec. ppm delay: 300 uSec. pulse shift polarity: positive). Can you check that all channels work as they should with the Rx connected to just one servo, same Tx settings, one ch...

Hi, I have a Turnigy 9x with the newest er9x firmware on it. The transmitter is a FrSky DJT module. As receiver I have a FrSky V8R7-II. Normally I use 7 channels with this reveiver but today I tried it with all 8 channels set and I had massive problems after take off: My copter did not react to my r...

I attached the config file for my TBS Discovery with APM 2.5 on board. For the six flight modes I use the three position switch and the AIL D/R switch. Channel 6 and Channel 7 is for configurating the APM.
Lioon

Ugh, why are you shouting all the time? That's annoying...

To your question: Which flight controller do you use? I could post the er9x configuration file for a quad with an APM 2.5 (and six flight modes), if that helps.

Lioon

Very, very cool! I love this firmware!
Thank you, ReST!

Lioon

Hi, I am wondering if the following problem is manageable with the er9x firmware. I have tried a long time but had no idea that worked. For my plane I want to add rudder to aileron movement. To programm this on the er9x is easy, I just added a Mixer which "translates" aileron movement to s...