Hardware was the issue. RST pin on 9x 64 chip not solderd properly. No conituity with multimeter test today. Fixed solder and now has conituity.
Flashed first try after fixing faulty solder.
Thanks for looking over my setup and throwing out ideas.
Search found 8 matches
- Sun Feb 24, 2013 5:20 pm
- Forum: PROGRAMMERS
- Topic: SCK error and Target dosn't answer
- Replies: 13
- Views: 23250
- Sun Feb 24, 2013 5:52 am
- Forum: PROGRAMMERS
- Topic: SCK error and Target dosn't answer
- Replies: 13
- Views: 23250
Re: SCK error and Target dosn't answer
I tested everything with a Multimeter and it appears the solder joint that connects the ATMEL chip to the 9x has a cold solder on the RST pin. I should have done this earlier...considering the bad workmanship overall of the radio. It just lookd good when I looked at it and I didnt have a meter. Foun...
- Sat Feb 23, 2013 7:49 pm
- Forum: PROGRAMMERS
- Topic: SCK error and Target dosn't answer
- Replies: 13
- Views: 23250
Re: SCK error and Target dosn't answer
The 9x screen shows 4.6v when the USB is plugged in...
Additionally the low voltage alarm does NOT beep when plugged into the programmer.
Additionally the low voltage alarm does NOT beep when plugged into the programmer.
- Sat Feb 23, 2013 6:57 pm
- Forum: PROGRAMMERS
- Topic: SCK error and Target dosn't answer
- Replies: 13
- Views: 23250
Re: SCK error and Target dosn't answer
From HK...
- Sat Feb 23, 2013 6:05 pm
- Forum: PROGRAMMERS
- Topic: SCK error and Target dosn't answer
- Replies: 13
- Views: 23250
Re: SCK error and Target dosn't answer
https://lh3.googleusercontent.com/-6uweGsKAzeA/USkDRaOYMdI/AAAAAAAAAMU/FvyKnGBQUp0/w486-h364-o-k/IMG_0147.JPG https://lh3.googleusercontent.com/-OqYra1VfDUA/USkDdX6sWuI/AAAAAAAAAMk/m_H3C3Ehr0Y/w486-h364-o-k/IMG_0150.JPG https://lh3.googleusercontent.com/-2foAdu6SO40/USkDLPu9-pI/AAAAAAAAAMM/TjRDiJP5...
- Sat Feb 23, 2013 5:34 pm
- Forum: PROGRAMMERS
- Topic: SCK error and Target dosn't answer
- Replies: 13
- Views: 23250
SCK error and Target dosn't answer
Hi, I am trying to flash my 9x with open 9x using Companion9x. I have checked the wireing..and I have a V2 board. I am using the HK USBasp. I have made no modifications to my transmiter. When I run Companion9x and try to flash I get the following error....... ----------------------------------------...
- Sun Jan 20, 2013 2:43 pm
- Forum: RF MODULES
- Topic: Continuity on flysky antenna solder pads...
- Replies: 4
- Views: 4358
Re: Continuity on flysky antenna solder pads...
So the inner conductor of the antenna coax goes to the center pad and the outer conducter/shiels goes to an outer pad? It has been a while since I took mine off and am finaly getting around to soldering it back and can't remember which one the center wire of the antenna connected to.
- Thu Jan 17, 2013 7:39 pm
- Forum: The Pickled Gnu (The Pub)
- Topic: New and saying Hi!
- Replies: 1
- Views: 2094
New and saying Hi!
Hi all, I am new to RC ....but learning fast. I already have the 9x and a FrSky telemetry module. I will be doing some Mods to allow flashing firmware and also getting the telemetry onscreen. I also intend to upgrade to Open LRS at some point and would like to intergrate that into my 9x. I am sure I...