openrcforums

ok got it solved thanks guys, I didn't know that it auto switches when binding and went to whatever the receiver was , that is what happened. the ar600 is dsmx11ms and the orange rx's are dsm2 , thanks again for all the help , I thought for sure I was gonna have to reflash.

I am in the same bind mode for the orange rx's as I am the radian, I can have 1 working but as soon as I bind to the one I loose the other, or does the orange dsm2 module switch automatically?

hi all I am using a turnigy 9x with er9x version 781 and all is good till now . I have been using the hobbyking orange rx receivers and have 8 models bound to the transmitter. I bought a parkzone Radian Pro glider yesterday and it came with a spectrum receiver ,it will bind but I lose the last model...

is it possible to bind to the nine eagles receivers? I have ER9X installed on the turnigy 9x transmitter , was wondering if this has been done. as i am thinking of buying a plane that is pnp that binds to the nine eagles protocal. thanks for any info. take care all

thanks for the information on the holder , i did not realise that was the problem , i thought it was the batteries where poping out of the holder, and thought that will be hard to do. thanks again i will check this stuff as well.

when pulling the batteries out of the 9x battery tray , i dont know how they could pop loose as some are saying that the batteries will come apart at the ends in the battery box , i had to pry them practically out , unless Hobbyking has fixed this issue as i was looking out for that issue.

i found an old 10hr timer charger for rechargable batteries that does 4 at a time it ,it outputs 250ma and has 10hr timer controlled , so i will just charge with this when needed and repeat twice as i have 8 batteries , is there any problems besides time waiting in this? i figure put them on over ni...

i am not using an intelligant charger it is a computerised charger , it is a V6AC which is like a turnigy acccell charger , I do not wish to put a resistor in the radio, what is the point in having a charge port in a radio if you can not use it to charge the batteries.getting frustrated with this th...

could i not just use a regular nicad or nimah charger that you would use to charge digital camera rechargeable batteries with? i have heard that this is hard on the batteries, i dont want to kill the batteries or the transmitter,

thanks for all the help , This is a great forum for the 9x, it never amazes me as to what the 9x is capable with the open software in it.

Yes you can use the charge port. The centre pin is positive. The only possible exception would be if you are using an intelligent charger that uses short discharge cycles to top off the battery pack, as that would not work properly due to the diode that is in line with the charger port that would s...

Nice, very good video thanks for the view

so i can use the charge port on the 9x with the original battery tray attached? would 10v for the low voltage alarm be to high (too soon to cut off) ? I do not mind charging , just dont want to do it all the time , was hoping i would get 4 or 5 days to the field and then charge the transmitter, lots...

There should be no problem using that pack.. I take it that it is a welded pack rather than individual cells? I like to follow old fashioned charge rates for my LSD pack and that is one tenth the capacity charge rate for 14 Hrs.. As for where to set the alarm.. Mine is set at 8.5 Volts. Not that I ...

after much reading on the subject , iam now totally confused . I would like to use 8 of the Turnigy LSD 2400 1.2v nimh batteries in my 9x , would this be too much power? I was gonna charge at 800mah as i understand that the 9x wont allow you to charge over 1amp which is ok with me. the other questio...

i meant to sa NO confusion instead of now ,

there actually is now confusion , and the way it is now works great so no need to try to confuse me now that i understand it. Lol

yes i am using eepe and down the road this what i will do for the triple rates. right now i just want it to say low or L .rather than M for medium, i realise it dont matter what it says as long as there is dual rates. down the road when i want triple rates then i will do that. it will take me years ...

what i did was set the sw1 to ELE and sw2 to ELE aswell and it gave me the low rates, it might not make sense to assign both sw1 and sw2 to the same , but this works. down the road i will do the trick with assigning a 3 pot switch with eepe .

thanks , i knew there had to be someway to do it, excellent radio firware , i just have to figure it all out, the manual didnt really say much , thanks again Mike , I appreciate the help

is there not low rates on ER9X ? all i can get is the M , and H , medium and high and i would like it to go low rates or is this not possible, I would love to be able to get this , please help, it is amazing to see such an amazing piece of software and no low rates, pulling my hair out here. and soo...

thanks , I was looking to change my name and this worked great.

all is good now, i have it bound to my sons mcx2 and also a foam board, the only thing now to do is figure out how to do the elevons for my other foamy , what a nice operating system and lots of options , i cant wait to put the flaps on my stinson and use the slow features for flaps, thanks again al...

do i have the right preferences set for eepe , i have default channel order AETR and for the mode i have mode 2 as that is what i fly, what should i have in those spots , in order for the channels to be right, I went into the mixes for the channelss and i did try 1-aileron 2-elevator, 3-throttle 4-r...

ok i got the ER9X flashed in the radio and am using the orange dsm2 module and i have it set for mode 2 . the channel order i set for default in eepe is AETR . so what am i doing wrong as i can bind to the receiver the channels just dont seem to be right yet. the throttle is on the right stick and s...

Ihave the Frsky module and the Orange Dsm2/Dsmx module the Orange Dsm2 module is the one giving me all the trouble it will not allow me operate the throttle on the left stick on 9x software, right now it seems to work sometimes and has a mind of its own and is on the right stick , on the Aileron cha...

thanks, will i be able to save stock firmware with companion 9x or avr8? i would like to be able to save this before flashing incase i need to or want to . thanks

hi all, i am planning on changing my firmware to the ER9X firmware and was wondering what to put for default channel order and default stick mode , I would like to use EEPE to save the original firmware and also the eeprom, but not sure on the order of the sticks and also i am planning on using the ...