Search found 1793 matches

by bob195558
Mon Feb 19, 2018 12:58 am
Forum: Feedback
Topic: DDOS filtering
Replies: 19
Views: 477

Re: DDOS filtering

NO, still have these fantom Photos popping in from nowhere and when adding Attachments/Add Files and pressing Preview and/or Submit I lose all but one Attachments/Add Files, File, but when posting it , it is all screwed up still. Seems to be a Fantom Attachments/Add Files somewhere doing its own thi...
by bob195558
Mon Feb 19, 2018 12:01 am
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 18
Views: 213

Re: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod

7) I use a (2S) 3 Pin JST-XH Extension Connector 250mm long and cut off the male end and pulled out the center Pin/wire and placed a black un-shrunk heat-shrink over the Red and Black wires. Next: Right Side of the TH3D EZABL Small Black Module Box, connect the Red wire to the top terminal and the ...
by bob195558
Sun Feb 18, 2018 11:00 pm
Forum: Feedback
Topic: DDOS filtering
Replies: 19
Views: 477

Re: DDOS filtering

I have not tried a very aggressive posting with multiple Photos yet,
but with this DDOS filtering turned OFF everything seem to work much better.
by bob195558
Sun Feb 18, 2018 10:44 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 18
Views: 213

Re: CR10 3D-Printer, TH3D EZABL Installation - Direct Wiring

6) Next: reinstall the bottom access panel to the CR10 Control Box and with the other end of the length of Gray Wire , strip the other end and connect it to the Left Side of the TH3D EZABL Small Black Module Box . Red Wire connects to the top terminal and the Black Wire connects to the bottom termi...
by bob195558
Sun Feb 18, 2018 12:33 pm
Forum: Feedback
Topic: DDOS filtering
Replies: 19
Views: 477

Re: DDOS filtering

Thank you João for the update, I pm Rob and have not heard anything from him.
This problem has been causing much frustration.

Bob B.
by bob195558
Sun Feb 18, 2018 1:28 am
Forum: Feedback
Topic: DDOS filtering
Replies: 19
Views: 477

Re: DDOS filtering

I can not fix it !
I can not remove the multiple Photos that this DDOS filter is strewing UP !
(http://openrcforums.com/forum/viewtopic ... 64#p135864).

I do not know where they all are coming from ? :?
by bob195558
Sun Feb 18, 2018 12:59 am
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 18
Views: 213

Re: CR10 3D-Printer, TH3D EZABL Installation - Direct Wiring

5) At the same time with your CR10 Control Box still open (optional),
you may want to check and Adjusting PSU Voltage and Stepper VREF Voltages.

See this TH3D video for info how to do this: (https://www.youtube.com/watch?v=pJRYXKRAUN4).

Adjusting PSU Voltage and Stepper VREF Voltages.jpg
by bob195558
Sun Feb 18, 2018 12:55 am
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 18
Views: 213

Re: CR10 3D-Printer, TH3D EZABL Installation - Direct Wiring

EZABL Sensor 2mm between Nozzle_b.jpg 4) Next: With the AC power disconnected from the CR10 Control Box, remove the bottom access panel and strip one end of the gray length of wire provided with the kit. Feed this wire in with the other cable wires into the back of the CR10 Control Box. EZABL 12V C...
by bob195558
Sat Feb 17, 2018 8:12 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 18
Views: 213

CR10 3D-Printer, TH3D EZABL Installation - Direct Wiring

TH3D EZABL Installation - Direct Wiring 1) Use the "TH3D EZABL Installation Guide.pdf " (https://www.th3dstudio.com/knowledge-base/ezabl-installation-guide/). 2) 3D Print the EZABL OEM Mount found on your Desktop: TH3D_UnifiedFirmware_U1.R1.1 / Mounts / CR-10 and CR-10S / EZABL OEM Mount / Stock18m...
by bob195558
Fri Feb 16, 2018 7:54 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 18
Views: 213

Re: CR10 3D-Printer, EZABL Bed Leveling / Flashing New TH3D Firmware to CR10 Melzi Control Board

Post Number: 10-B 24) Next: In TH3D EXTRAS I did change the " #define EZABL_POINTS 4 " to " #define EZABL_POINTS 5 " because the un-flatness of my Print Bed . 25) Next: Pressing the Upload button and firmware will start compiling the firmware before it Uploads to your CR10 Melzi Control Board. Ardu...
by bob195558
Fri Feb 16, 2018 7:45 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 18
Views: 213

Re: CR10 3D-Printer, EZABL Bed Leveling / Flashing New TH3D Firmware to CR10 Melzi Control Board

Post Number: 9-B Flashing New TH3D Firmware to CR10 Melzi Control Board 19) Next view: TH3D Unified Firmware Setup Guide - Stock, EZABL, EZOut and More! Youtube video here: (https://www.youtube.com/watch?v=B2ODwmiMNhc). View the whole video first, before pressing the " Upload " button, so that you ...
by bob195558
Fri Feb 16, 2018 5:56 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 18
Views: 213

Re: CR10 3D-Printer, EZABL Bed Leveling / Flashing Bootloader to CR10 Melzi Control Board

Post Number: 8-B 10) Next: go and select: Tools / Board: "Sanguino(1284P Boards)" / Sanguino(1284P Boards) 11) Next: go and select: Tools / Processor / "ATmega1284 or ATmega1284P (16MHz)" / ATmega1284 or ATmega1284P (16MHz) 12) Next: go and select: Tools / Port: "COM6(Arduino Uno)" / COM6(Arduino U...
by bob195558
Fri Feb 16, 2018 5:56 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 18
Views: 213

Re: CR10 3D-Printer, EZABL Bed Leveling / Flashing Bootloader to CR10 Melzi Control Board

Post Number: 7-B 8) Next Select: Tools / Programmer: Arduino as ISP 9) Next select: Upload You will see lights flashing in their proper sequence of uploading sketch to the UNO board. Note you may see an error message after compiling and uploading. See error message below which I disregarded. ======...
by bob195558
Fri Feb 16, 2018 5:24 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 18
Views: 213

Re: CR10 3D-Printer, EZABL Bed Leveling /Flashing Bootloader to CR10 Melzi Control Board

Post Number: 6-B

7) Next Select: Tools / Port: "COM6(Arduino Uno)" / COM6(Arduino Uno)
Note you may see something different like this: COM6(Arduino/Genuino Uno)
CR10 Bootloder Flash_3b.jpg
3b
by bob195558
Fri Feb 16, 2018 5:17 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 18
Views: 213

Re: CR10 3D-Printer, EZABL Bed Leveling / Flashing Bootloader to CR10 Melzi Control Board

Post Number: 5-B

6) Next go to: Tools / Board: "Sanguino(1284P Boards)" / Sanguino(1284P Boards)
Note: You may see something different like this: Arduino/Genuino Uno
CR10 Bootloder Flash_4d.jpg
by bob195558
Fri Feb 16, 2018 5:00 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 18
Views: 213

Re: CR10 3D-Printer, EZABL Bed Leveling / Flashing Bootloader to CR10 Melzi Control Board

Post Number: 4-B

5) Next go to: Files / Examples / 11.ArduinoISP / ArduinoISP
This opens a new Sketch (ArduinoISP) which you will now use.
CR10 Bootloder Flash_3c.jpg
by bob195558
Fri Feb 16, 2018 4:59 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 18
Views: 213

Re: CR10 3D-Printer, EZABL Bed Leveling / Flashing Bootloader to CR10 Melzi Control Board

Post Number: 3-B 3) Go to the CR10 Bootloader Flashing Guide find here: (https://www.th3dstudio.com/knowledge-base/cr-10-bootloader-flashing-guide/) and/or youtube: (https://www.youtube.com/watch?time_continue=23&v=27RDXtKjrCI) and follow the instructions. 4) With the UNO and CR10 Melzi Control boa...
by bob195558
Fri Feb 16, 2018 3:39 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 18
Views: 213

Re: CR10 3D-Printer, EZABL Bed Leveling /Flashing Bootloader to CR10 Melzi Control Board

Post Number: 2-B 1) Download this Creality CR10 firmware folded pack "TH3D_UnifiedFirmware_U1.R1.1" find here: (https://www.th3dstudio.com/knowledgebase/). Unzip and place this folder on your desktop. 2) Open sub-folder "Windows Arduino" and click on "arduino.exe" to open the Arduino program. And/o...
by bob195558
Fri Feb 16, 2018 3:27 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 18
Views: 213

Re: CR10 3D-Printer, EZABL Bed Leveling / Flashing Bootloader to CR10 Melzi Control Board

Post Number: 1-B Flashing Bootloader and New TH3D Firmware to CR10 Melzi Control Board. I removed the CR10 Melzi Control Board from its control box and using an Arduino UNO Board to flash the new Bootloader to the CR10 Melzi Control Board. For wiring instructions I used the TH3D youtube video: (htt...
by bob195558
Fri Feb 16, 2018 2:27 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 18
Views: 213

Re: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod

Note: I will have to break the next post up into several post because of the Faulty "DDOS filtering" that is managing this great forum. See hear for more info about this Faulty "DDOS filtering" : (http://openrcforums.com/forum/viewtopic.php?f=3&t=10615) and (http://openrcforums.com/forum/viewtopic....
by bob195558
Thu Feb 15, 2018 9:47 am
Forum: Feedback
Topic: DDOS filtering
Replies: 19
Views: 477

Re: DDOS filtering

Hi Rob Thomson, This DDOS filtering really stinks (screwing up the work here), can this be fixed ? :?: I can not post several photos to at the same time. While uploading the second or third photo, one of the previous photos will disappear before I even try to submit the new post. And loses Photos ! ...
by bob195558
Sat Jan 27, 2018 6:40 pm
Forum: Other Electronic Projects
Topic: 3D PRINTING (RC Hobby for 3D Printers)
Replies: 51
Views: 895

Re: 3D PRINTING (RC Hobby for 3D Printers)

Another upgrade/mod for the CR10 3D Printer (EZABL Auto Bed Leveling): (http://openrcforums.com/forum/viewtopic ... 85&t=10815).
This (https://www.th3dstudio.com/product/ezab ... cr-10-abl/) will fix the Print Bed nonflatness.


Bob B.
by bob195558
Sat Jan 27, 2018 6:31 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 18
Views: 213

Printing CR10 EZABL Sensor Mount for auto Bed Leveling/Tramming

3D Printed the EZABL Stock Sensor Mount First time using " SUPPORT " in the Cura 3.1.0 slicer software and first time using the eSUN WOOD (brown) filament, which is a little less brittle than the eSUN PLA+ (blue). TH3D EZABL 18mm Mount for CR10_a.jpg TH3D EZABL 18mm Mount for CR10_b.jpg
by bob195558
Sat Jan 27, 2018 5:30 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 18
Views: 213

CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod

I have ordered from TH3D (Timothy Hoogland) the EZABL Direct Wire, Auto Bed Leveling Upgrade/Mod for the CR10 3D Printer: (https://www.th3dstudio.com/product/ezabl-kit-direct-wire/). EZABL Bed Leveling _Direct Wired_.gif TH3D EZABL Guide V151.zip Because the aluminum heated Print Bed plate is not fl...
by bob195558
Tue Jan 23, 2018 9:55 pm
Forum: Other Electronic Projects
Topic: 3D PRINTING (RC Hobby for 3D Printers)
Replies: 51
Views: 895

Re:Wireless SD-Card Mod Upgrade for CR-10 3D Printer

In the process of doing another Mod Upgrade to CR-10 3D Printer. Mod Upgrade to a Wireless SD-Card No need to physically move .gcode file to CR-10 3D Printer anymore. :D 1) 3D Printed Wireless SD-Card Holder: (https://www.thingiverse.com/thing:2570622). SD Card Holder for CR10.jpg 2) Ordered parts: ...
by bob195558
Sat Jan 20, 2018 6:28 pm
Forum: Other Electronic Projects
Topic: 3D PRINTING (RC Hobby for 3D Printers)
Replies: 51
Views: 895

3D PRINTING (Fusion 360 Autodesk 9x Radio Case)

Update: Been learning how to use Fusion 360 Autodesk and only have so far a very rough sketch of the 9x front case half. I have been allowing myself to start from the beginning many times sketching a new version so to help gain in learning to use Fusion 360. 9x Front Case half Fusion360_a.jpg The 9...
by bob195558
Sat Jan 20, 2018 4:22 pm
Forum: Feedback
Topic: DDOS filtering
Replies: 19
Views: 477

Re: DDOS filtering

Seem like this new filter, DDOS has a timer that times-out disconnecting us from the Openrcforums and so when we select a function like "Preview" or "Submit" and/or downloading Photos ("Attachments") to add, maybe be causing the lost of our created info to be lost. I do not know the cause of the dif...
by bob195558
Sat Jan 20, 2018 10:11 am
Forum: Feedback
Topic: DDOS filtering
Replies: 19
Views: 477

Re: DDOS filtering

Things continue to be screwed up with when posting for me.
clear cookies/cache did nothing for me.

Bob B.
by bob195558
Sat Jan 13, 2018 6:22 pm
Forum: Other Electronic Projects
Topic: 3D PRINTING (RC Hobby for 3D Printers)
Replies: 51
Views: 895

Re: 3D PRINTING (RC Hobby for 3D Printers)

A little update, been working with the CR10 3D printer, printing some parts from thingiverse: (https://www.thingiverse.com/search?q=9x+&sa=&dwh=125a5a356bd24b4) to learn how to best 3D print parts. I am using Curs 3.1.0 for the slicer program. Because the heated aluminum bed is not flat, I have bee...

Go to advanced search