Search found 1797 matches

by bob195558
Wed Feb 21, 2018 1:20 pm
Forum: Feedback
Topic: DDOS filtering
Replies: 20
Views: 515

Re: DDOS filtering

All fixed now!
Rob
Thank you for your time fixing the disappearing and mixing up attachment files. :D
by bob195558
Tue Feb 20, 2018 12:07 am
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 21
Views: 267

Re: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod

10) Next: TH3D EZABL New Slicer Starting Gcodes February 20, 2018 Need to update your Slicer program with the new TH3D ABL Starting Gcodes. Updating Slicer Cura 3.1 program with the new ABL Starting Gcodes. Find Cura Starting Gcodes: Preferences / Printers / Machine Settings / Starting Gcodes. Repl...
by bob195558
Mon Feb 19, 2018 6:28 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 21
Views: 267

Re: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod

9) Next: (a) Pre Heat Printer Bed using "Preheat PLA" (b) Disable Stepper Motors (c) You can, by hand turn the Z-Axis down to where the Nozzle is a paper thickness away form the Heating Bed surface. (d) Next: you may need to adjust the Sensitivity of the EZABL Sensor. This can done by turning the v...
by bob195558
Mon Feb 19, 2018 2:42 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 21
Views: 267

Re: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod

8) Next: Test your EZABL Sensor that it is detecting properly. Power Up your CR10 3D Printer and using your finger slow move it up toward the bottom of the EZABL Sensor and when your finger comes close enough, you will see the 1st LED on the top of the EZABL Sensor and a 2nd LED in the TH3D EZABL S...
by bob195558
Mon Feb 19, 2018 12:58 am
Forum: Feedback
Topic: DDOS filtering
Replies: 20
Views: 515

Re: DDOS filtering

NO, still have these Phantom Photos popping in from nowhere and when adding Attachments/Add Files and pressing Preview and/or Submit I lose all, but one Photo Attachments/Add Files, File, but when posting it , it is all screwed up still. Seems to be Phantom Photos in a Phantom Attachments/Phantom Ad...
by bob195558
Mon Feb 19, 2018 12:01 am
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 21
Views: 267

Re: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod

7) I use a (2S) 3 Pin JST-XH Extension Connector 250mm long and cut off the male end and pulled out the center Pin/wire and placed a black un-shrunk heat-shrink over the Red and Black wires. Next: Right Side of the TH3D EZABL Small Black Module Box, connect the Red wire to the top terminal and the ...
by bob195558
Sun Feb 18, 2018 11:00 pm
Forum: Feedback
Topic: DDOS filtering
Replies: 20
Views: 515

Re: DDOS filtering

I have not tried a very aggressive posting with multiple Photos yet,
but with this DDOS filtering turned OFF everything seem to work much better.
by bob195558
Sun Feb 18, 2018 10:44 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 21
Views: 267

Re: CR10 3D-Printer, TH3D EZABL Installation - Direct Wiring

6) Next: reinstall the bottom access panel to the CR10 Control Box and with the other end of the length of Gray Wire , strip the other end and connect it to the Left Side of the TH3D EZABL Small Black Module Box . Red Wire connects to the top terminal and the Black Wire connects to the bottom termi...
by bob195558
Sun Feb 18, 2018 12:33 pm
Forum: Feedback
Topic: DDOS filtering
Replies: 20
Views: 515

Re: DDOS filtering

Thank you João for the update, I pm Rob and have not heard anything from him.
This problem has been causing much frustration.

Bob B.
by bob195558
Sun Feb 18, 2018 1:28 am
Forum: Feedback
Topic: DDOS filtering
Replies: 20
Views: 515

Re: DDOS filtering

I can not fix it !
I can not remove the multiple Photos that this DDOS filter is strewing UP !
(http://openrcforums.com/forum/viewtopic ... 64#p135864).

I do not know where they all are coming from ? :?
by bob195558
Sun Feb 18, 2018 12:59 am
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 21
Views: 267

Re: CR10 3D-Printer, TH3D EZABL Installation - Direct Wiring

5) At the same time with your CR10 Control Box still open (optional),
you may want to check and Adjusting PSU Voltage and Stepper VREF Voltages.

See this TH3D video for info how to do this: (https://www.youtube.com/watch?v=pJRYXKRAUN4).

Adjusting PSU Voltage and Stepper VREF Voltages.jpg
by bob195558
Sun Feb 18, 2018 12:55 am
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 21
Views: 267

Re: CR10 3D-Printer, TH3D EZABL Installation - Direct Wiring

4) Next: With the AC power disconnected from the CR10 Control Box, remove the bottom access panel and strip one end of the gray length of wire provided with the kit. Feed this wire in with the other cable wires into the back of the CR10 Control Box. EZABL 12V Connection_b.jpg Attach the RED Wire to...
by bob195558
Sat Feb 17, 2018 8:12 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 21
Views: 267

CR10 3D-Printer, TH3D EZABL Installation - Direct Wiring

TH3D EZABL Installation - Direct Wiring 1) Use the "TH3D EZABL Installation Guide.pdf " (https://www.th3dstudio.com/knowledge-base/ezabl-installation-guide/). 2) 3D Print the EZABL OEM Mount found on your Desktop: TH3D_UnifiedFirmware_U1.R1.1 / Mounts / CR-10 and CR-10S / EZABL OEM Mount / Stock18m...
by bob195558
Fri Feb 16, 2018 7:54 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 21
Views: 267

Re: CR10 3D-Printer, EZABL Bed Leveling / Flashing New TH3D Firmware to CR10 Melzi Control Board

Post Number: 10-B 24) Next: In TH3D EXTRAS I did change the " #define EZABL_POINTS 4 " to " #define EZABL_POINTS 5 " because the un-flatness of my Print Bed . 25) Next: Pressing the Upload button and firmware will start compiling the firmware before it Uploads to your CR10 Melzi Control Board. Ardu...
by bob195558
Fri Feb 16, 2018 7:45 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 21
Views: 267

Re: CR10 3D-Printer, EZABL Bed Leveling / Flashing New TH3D Firmware to CR10 Melzi Control Board

Post Number: 9-B Flashing New TH3D Firmware to CR10 Melzi Control Board 19) Next view: TH3D Unified Firmware Setup Guide - Stock, EZABL, EZOut and More! Youtube video here: (https://www.youtube.com/watch?v=B2ODwmiMNhc). View the whole video first, before pressing the " Upload " button, so that you ...
by bob195558
Fri Feb 16, 2018 5:56 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 21
Views: 267

Re: CR10 3D-Printer, EZABL Bed Leveling / Flashing Bootloader to CR10 Melzi Control Board

Post Number: 8-B 10) Next: go and select: Tools / Board: "Sanguino(1284P Boards)" / Sanguino(1284P Boards) 11) Next: go and select: Tools / Processor / "ATmega1284 or ATmega1284P (16MHz)" / ATmega1284 or ATmega1284P (16MHz) 12) Next: go and select: Tools / Port: "COM6(Arduino Uno)" / COM6(Arduino U...
by bob195558
Fri Feb 16, 2018 5:56 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 21
Views: 267

Re: CR10 3D-Printer, EZABL Bed Leveling / Flashing Bootloader to CR10 Melzi Control Board

Post Number: 7-B 8) Next Select: Tools / Programmer: Arduino as ISP 9) Next select: Upload You will see lights flashing in their proper sequence of uploading sketch to the UNO board. Note you may see an error message after compiling and uploading. See error message below which I disregarded. ======...
by bob195558
Fri Feb 16, 2018 5:24 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 21
Views: 267

Re: CR10 3D-Printer, EZABL Bed Leveling /Flashing Bootloader to CR10 Melzi Control Board

Post Number: 6-B

7) Next Select: Tools / Port: "COM6(Arduino Uno)" / COM6(Arduino Uno)
Note you may see something different like this: COM6(Arduino/Genuino Uno)
CR10 Bootloder Flash_3b.jpg
3b
by bob195558
Fri Feb 16, 2018 5:17 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 21
Views: 267

Re: CR10 3D-Printer, EZABL Bed Leveling / Flashing Bootloader to CR10 Melzi Control Board

Post Number: 5-B

6) Next go to: Tools / Board: "Sanguino(1284P Boards)" / Sanguino(1284P Boards)
Note: You may see something different like this: Arduino/Genuino Uno
CR10 Bootloder Flash_4d.jpg
by bob195558
Fri Feb 16, 2018 5:00 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 21
Views: 267

Re: CR10 3D-Printer, EZABL Bed Leveling / Flashing Bootloader to CR10 Melzi Control Board

Post Number: 4-B

5) Next go to: Files / Examples / 11.ArduinoISP / ArduinoISP
This opens a new Sketch (ArduinoISP) which you will now use.
CR10 Bootloder Flash_3c.jpg
by bob195558
Fri Feb 16, 2018 4:59 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 21
Views: 267

Re: CR10 3D-Printer, EZABL Bed Leveling / Flashing Bootloader to CR10 Melzi Control Board

Post Number: 3-B 3) Go to the CR10 Bootloader Flashing Guide find here: (https://www.th3dstudio.com/knowledge-base/cr-10-bootloader-flashing-guide/) and/or youtube: (https://www.youtube.com/watch?time_continue=23&v=27RDXtKjrCI) and follow the instructions. 4) With the UNO and CR10 Melzi Control boa...
by bob195558
Fri Feb 16, 2018 3:39 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 21
Views: 267

Re: CR10 3D-Printer, EZABL Bed Leveling /Flashing Bootloader to CR10 Melzi Control Board

Post Number: 2-B 1) Download this Creality CR10 firmware folded pack "TH3D_UnifiedFirmware_U1.R1.1" find here: (https://www.th3dstudio.com/knowledgebase/). Unzip and place this folder on your desktop. 2) Open sub-folder "Windows Arduino" and click on "arduino.exe" to open the Arduino program. And/o...
by bob195558
Fri Feb 16, 2018 3:27 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 21
Views: 267

Re: CR10 3D-Printer, EZABL Bed Leveling / Flashing Bootloader to CR10 Melzi Control Board

Post Number: 1-B Flashing Bootloader and New TH3D Firmware to CR10 Melzi Control Board. I removed the CR10 Melzi Control Board from its control box and using an Arduino UNO Board to flash the new Bootloader to the CR10 Melzi Control Board. For wiring instructions I used the TH3D youtube video: (htt...
by bob195558
Fri Feb 16, 2018 2:27 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 21
Views: 267

Re: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod

Flashing Bootloader and New TH3D Firmware to CR10 Melzi Control Board.
For the EZABL Sensor installation.
by bob195558
Thu Feb 15, 2018 9:47 am
Forum: Feedback
Topic: DDOS filtering
Replies: 20
Views: 515

Re: DDOS filtering

Hi Rob Thomson, This DDOS filtering really stinks (screwing up the work here), can this be fixed ? :?: I can not post several photos to at the same time. While uploading the second or third photo, one of the previous photos will disappear before I even try to submit the new post. And loses Photos ! ...
by bob195558
Sat Jan 27, 2018 6:40 pm
Forum: Other Electronic Projects
Topic: 3D PRINTING (RC Hobby for 3D Printers)
Replies: 51
Views: 906

Re: 3D PRINTING (RC Hobby for 3D Printers)

Another upgrade/mod for the CR10 3D Printer (EZABL Auto Bed Leveling): (http://openrcforums.com/forum/viewtopic ... 85&t=10815).
This (https://www.th3dstudio.com/product/ezab ... cr-10-abl/) will fix the Print Bed nonflatness.


Bob B.
by bob195558
Sat Jan 27, 2018 6:31 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 21
Views: 267

Printing CR10 EZABL Sensor Mount for auto Bed Leveling/Tramming

3D Printed the EZABL Stock Sensor Mount First time using " SUPPORT " in the Cura 3.1.0 slicer software and first time using the eSUN WOOD (brown) filament, which is a little less brittle than the eSUN PLA+ (blue). TH3D EZABL 18mm Mount for CR10_a.jpg TH3D EZABL 18mm Mount for CR10_b.jpg
by bob195558
Sat Jan 27, 2018 5:30 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod
Replies: 21
Views: 267

CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod

I have ordered from TH3D (Timothy Hoogland) the EZABL Direct Wire, Auto Bed Leveling Upgrade/Mod for the CR10 3D Printer: (https://www.th3dstudio.com/product/ezabl-kit-direct-wire/). EZABL Bed Leveling _Direct Wired_.gif TH3D EZABL Guide V151.zip Because the aluminum heated Print Bed plate is not fl...
by bob195558
Tue Jan 23, 2018 9:55 pm
Forum: Other Electronic Projects
Topic: 3D PRINTING (RC Hobby for 3D Printers)
Replies: 51
Views: 906

Re:Wireless SD-Card Mod Upgrade for CR-10 3D Printer

In the process of doing another Mod Upgrade to CR-10 3D Printer. Mod Upgrade to a Wireless SD-Card No need to physically move .gcode file to CR-10 3D Printer anymore. :D 1) 3D Printed Wireless SD-Card Holder: (https://www.thingiverse.com/thing:2570622). SD Card Holder for CR10.jpg 2) Ordered parts: ...

Go to advanced search