Search found 1829 matches

by bob195558
Thu Apr 19, 2018 1:45 pm
Forum: er9x
Topic: Audio (voice) - Stock 9X PCB
Replies: 4067
Views: 314122

Re: Audio (voice) - Stock 9X PCB (AR9x board)

The AR9x replacement board, when it was available, did cost much less: (http://www.ar9x.net/).
by bob195558
Thu Apr 19, 2018 1:06 pm
Forum: er9x
Topic: Audio (voice) - Stock 9X PCB
Replies: 4067
Views: 314122

Re: Audio (voice) - Stock 9X PCB (9Xtreme-2)

Jun 01, 2016, s_mack: 9Xtreme V2? Or Discontinued ? (http://openrcforums.com/forum/viewtopic.php?f=126&t=8895). I appreciate that. Regarding the reverse polarity... you may be surprised at how many of the 1000pcs went to replacing blown up units :) Regarding sales, risk, etc... it is an expensive pr...
by bob195558
Thu Apr 19, 2018 12:30 pm
Forum: er9x
Topic: Audio (voice) - Stock 9X PCB
Replies: 4067
Views: 314122

Re: Audio (voice) - Stock 9X PCB (9Xtreme-2)

50€ is about $62 + shipping + other components + soldering = more dollars and the skill and time to assemble. Would the chip need to be flash too ? (http://openrcforums.com/forum/viewtopic.php?f=95&t=7182) (http://openrcforums.com/forum/viewforum.php?f=126) It would be good to have 9Xtreme-2 though ...
by bob195558
Tue Apr 17, 2018 11:10 pm
Forum: er9x
Topic: Audio (voice) - Stock 9X PCB
Replies: 4067
Views: 314122

Re: Audio (voice) - Stock 9X PCB (9Xtreme-2)

Could a Raspberry Pi be used ?
by bob195558
Tue Apr 17, 2018 9:56 pm
Forum: Hardware
Topic: Replacing Atmega64 with 128
Replies: 14
Views: 627

Re: Replacing Atmega64 with 128

Go to (http://www.er9x.com/) and then select: er9x for Mega2561 processor (right click and select 'save as') This file has been updated since 2014, but this is the one you would use for the M2561 chip. I think see here using eepe to flash with: (http://openrcforums.com/forum/viewtopic.php?f=95&t=381...
by bob195558
Mon Apr 16, 2018 11:56 am
Forum: Hardware
Topic: Any 9x upgrade boards available???
Replies: 3
Views: 122

Re: Any 9x upgrade boards available???

ErSky9x on Taranis-Plus is a good option too.
by bob195558
Sat Apr 14, 2018 2:04 pm
Forum: Turnigy 9XR radio
Topic: 9XR & Frsky XJT Telemetry
Replies: 60
Views: 7651

Re: 9XR & Frsky XJT Telemetry

Thanks João, I missed that when I saw the Pro in the firmware version er9xProv822f.
I should have noitic the er9x in front of it.
Many people leave off the Pro when referring to the 9XR-Pro radios.
by bob195558
Sat Apr 14, 2018 11:19 am
Forum: Turnigy 9XR radio
Topic: 9XR & Frsky XJT Telemetry
Replies: 60
Views: 7651

Re: 9XR & Frsky XJT Telemetry

Hi. I have a problem and need help. I have a Turnigy 9XR radio after modifying telemetry. Set -> 9XR + DJT + D8R-II Plus - works perfectly. Because I need more channels I bought XJT + X8R Unfortunately, I can not run RSSI and SWR telemetry on 9XR + XJT My software is er9x Pro v822f - XJT protocol (...
by bob195558
Fri Apr 13, 2018 5:16 pm
Forum: Hardware
Topic: Replacing Atmega64 with 128
Replies: 14
Views: 627

Re: Replacing Atmega64 with 128

about fuses, no Not a problem, as you can see Mike and João helped me through flashing the new m2561 Chip.
They would be happy to help you also and you will love the m2561 Chip.
Mike has, using eepe to flash m2561 Chip, which helps a lot too.

Bob B.
by bob195558
Mon Apr 09, 2018 4:28 pm
Forum: FrSky Taranis radio
Topic: Taranis X9D aileron trim strange behavior
Replies: 10
Views: 2471

Re: Taranis X9D aileron trim strange behavior

You may want to order a replacement Trim Switch Board, so if the problem returns, you may want to try a new Trim Switch Board. Also follow Mike's request first (if/when problem returns), as he is best to help you with solving this problem. Have you checked in the switch diag menu to see the trim swi...
by bob195558
Sun Apr 08, 2018 11:10 am
Forum: FrSky Taranis radio
Topic: Taranis X9D aileron trim strange behavior
Replies: 10
Views: 2471

Re: Taranis X9D aileron trim strange behavior

Trim switch still maybe faulty. (https://alofthobbies.com/frsky-taranis- ... witch.html)
Try swapping the two horizontals trim switch boards to see if
the problem follows the same horizontal trim switch board.
by bob195558
Sat Apr 07, 2018 2:19 pm
Forum: FrSky Taranis radio
Topic: Taranis X9D aileron trim strange behavior
Replies: 10
Views: 2471

Re: Taranis X9D aileron trim strange behavior

I suggest the problem is a hardware problem, that maybe with a sticky switch trim button,
which may fix itself by moving the trim switch back and forth several times.
But this is only a guess, as not having your radio in hand.
Let us know what you find.
by bob195558
Sat Apr 07, 2018 1:41 pm
Forum: Hardware
Topic: Replacing Atmega64 with 128
Replies: 14
Views: 627

Re: Replacing Atmega64 with 128

Here is info about replacing the Chip if you are still interested:
(http://openrcforums.com/forum/viewtopic ... 120#p74046).
It is best to upgrade to the m2561 as you will have more capabilities, the 128 will give you less capabilities. :)
by bob195558
Sat Mar 24, 2018 12:40 pm
Forum: Turnigy 9XR PRO radio
Topic: 9XR-Pro Radios from HobbyKing on Sale
Replies: 29
Views: 1547

eePe and eePskye simplified programming

I think, where to be looking, to make more simplified programming, is not so much with er9x and erSky9x radio firmware, but to make simplified programming in eePe and eePskye. There could also be eePe and eePskye apps for computer phones and tablets, with WiFi connection back to the radio too. EePe ...
by bob195558
Sat Mar 24, 2018 11:38 am
Forum: General help (FrSky Taranis radio)
Topic: Am i heading to hell
Replies: 9
Views: 500

Re: Am i heading to hell

Kilrah wrote:
Sun Jan 03, 2016 2:32 pm
The change only affects X series. There has been no change to D.
by bob195558
Fri Mar 23, 2018 10:15 pm
Forum: General help (FrSky Taranis radio)
Topic: Am i heading to hell
Replies: 9
Views: 500

Re: Am i heading to hell

I believe all older (Pre EU afflictions) and new D and V series are EU lawful.
by bob195558
Fri Mar 23, 2018 8:50 pm
Forum: Turnigy 9XR PRO radio
Topic: 9XR-Pro Radios from HobbyKing on Sale
Replies: 29
Views: 1547

er9x and erSky9x firmware

ErSky9x and Opentx are the leading RC radio operating systems in the world. All the other are trying to copy just some of the capabilities which these two RC radio systems are doing. ErSky9x works on the Ar9x, Sky9x, 9xr-pro, 9xtreme, Taranis-X9D, Taranis-Plus, Taranis-QX7 and Taranis-X9E Er9x firmw...
by bob195558
Fri Mar 23, 2018 2:47 pm
Forum: Turnigy 9XR PRO radio
Topic: 9XR-Pro Radios from HobbyKing on Sale
Replies: 29
Views: 1547

Re: 9XR-Pro Radios from HobbyKing on Sale

Hi SkyNorth, I have one of your last Sky9x boards and like it a lot. It just seems to work/run really smoothly, which I believe is saying a lot to the really excellent job you did designing it. :D Combined with Mike B's ersky9x firmware which is also a very well done excellent job designing the erSk...
by bob195558
Fri Mar 23, 2018 1:46 pm
Forum: General help (FrSky Taranis radio)
Topic: Am i heading to hell
Replies: 9
Views: 500

Re: Am i heading to hell

Also better to use the X series receivers which you will then have Telemetry data.
The V-series receivers do not send telemetry information back to the transmitter.
by bob195558
Thu Mar 22, 2018 3:49 pm
Forum: Turnigy 9XR PRO radio
Topic: 9XR-Pro Radios from HobbyKing on Sale
Replies: 29
Views: 1547

Re: 9XR-Pro Radios from HobbyKing on Sale

I never found it on Hobbyking at this price (though following the link in their emails). I always get the "out of stock" pages with a price of over 50 or 60 $ I believe it is hard to change Gimbals to Mode 2. It's doable. I did it two weeks ago. Reinhard So if someone wanted a 9XR-Pro Mode 2 (at a ...
by bob195558
Thu Mar 22, 2018 2:21 pm
Forum: Turnigy 9XR PRO radio
Topic: 9XR-Pro Radios from HobbyKing on Sale
Replies: 29
Views: 1547

9XR-Pro Radios from HobbyKing on Sale

For who like 9XR-Pro radios, HobbyKing has some available again. Sale $29.95 on the Turnigy 9XR PRO Radio Transmitter Mode 1 (without module): (https://hobbyking.com/en_us/turnigy-9xr-pro-radio-transmitter-mode-1-without-module.html). I believe it is hard to change Gimbals to Mode 2 . $63.63 (Out of...
by bob195558
Thu Mar 22, 2018 1:18 am
Forum: Hardware
Topic: Antenna replacement
Replies: 11
Views: 837

Re: Antenna replacement

RF Power Meter.jpg
RF Power Meter
This can help to measure how well different antennas are working: (http://www.immersionrc.com/downloads/ma ... Manual.pdf)
by bob195558
Wed Mar 14, 2018 11:13 am
Forum: Hardware
Topic: Antenna replacement
Replies: 11
Views: 837

Re: Antenna replacement

by bob195558
Mon Mar 12, 2018 5:40 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade Mod
Replies: 26
Views: 2650

CR10 3D-Printer, Updating TH3D Unified Firmware

Flashing Updated TH3D Unified Firmware to the CR10 Melzi Control Board 1) CR10 Melzi Control Board with the Bootloader installed, download the newest TH3D Unified Firmware : (https://www.th3dstudio.com/knowledge-base/th3d-unified-firmware/). As of March 10, 2018 the newest TH3D Unified Firmware ver...
by bob195558
Fri Mar 09, 2018 11:30 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade Mod
Replies: 26
Views: 2650

CR10 3D-Printer, P.I.D. Auto Tuning Hotend Temperature

3D Printer P.I.D. Auto Tuning Hotend Temperature What is P.I.D. Tuning? P. I. D. (Proportional Integral Derivative) is the system the printers use for holding a set temperature. This system controls how fast the printer reaches the set temperature and how well it holds that temperature once it gets...
by bob195558
Sun Mar 04, 2018 1:08 am
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade Mod
Replies: 26
Views: 2650

Re: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod

Z Offset BabyStepping Feature Z Offset BabyStepping Feature, is used to quickly adjust the gap between the Nozzle and the heated Print Bed (paper thickness of .004" / 0.1mm). Z BabyStepping Feature can be done on-the-fly, while you are printing. To use BabyStepping, Press the Menu Button 2 times (p...
by bob195558
Wed Feb 28, 2018 2:16 am
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade Mod
Replies: 26
Views: 2650

Re: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod

12 ) Next: If you want to send Gcode Commands and do not have Simplify3D or Octoprint, you can uses " Gcode Sender - Pronterface " to USB connect between your PC and CR10 Printer. Download Pronterface here: (https://www.th3dstudio.com/knowledge-base/gcode-sender-pronterface/) Gcode Sender_Pronterfa...
by bob195558
Wed Feb 28, 2018 2:06 am
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade Mod
Replies: 26
Views: 2650

Re: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade / Mod

11 ) Next: I did a test 3D Print using the USB connection between Slicer Cura and the CR10 3D Printer. You can do your test 3D Print using your selected gcode (3D print) with your SD card if you so like to do also. I printed right to the Glass Heated Print Bed using temperatures of 65 C and the Noz...
by bob195558
Mon Feb 26, 2018 11:46 am
Forum: 9Xtreme upgrade board
Topic: My 9Xtreme Installation
Replies: 210
Views: 27414

Re: My 9Xtreme Installation

Maybe good time for HobbyKing to produce a 9x with the Sky-Board and Hall Sensor Gimbal.
Would sell very well.
by bob195558
Sun Feb 25, 2018 11:40 pm
Forum: 9Xtreme upgrade board
Topic: My 9Xtreme Installation
Replies: 210
Views: 27414

Re: My 9Xtreme Installation

Daedalus66 wrote:
Sun Feb 25, 2018 10:29 pm
“Bad” in what sense? It’s big enough for 6 AA cells.
“Bad” in the sense, do not want AA batteries because Lipo are a lot better and 9x more able to use different forms (shapes) of batteries.

Go to advanced search