openrcforums

Hey guys, im getting a lot of interference on the rev b boards speaker from my nearby rangelink 433 tx module. Sounds like i have aliens in the room, can anyone suggest a way to get rid of it without moving either one?

Maybe a filter or special wire of some sort?

Any way to integrate the two? Micro network card?

Who has a stock board?

Has anyone loaded open9x just using samba?

If your talking to me, its a rev b board from ersky

I remember spending an entire day a few months ago before I got this working. I refuse to waste today on this. Can anyone figure out why companion9x is so hard to get working?

http://www.youtube.com/watch?v=mLbE91morAk

Well just swapped the two Up and Down wires around and now everything is fine!

Nevermind, i got it. This is the right way I think. Now everthing works except my up and down keys are reversed?

Did I jumper the right four? I did a "kaos" install with wires instead of pins. Im having the same problem he had, no left or up. Its a sky9x rev b board.

Bertrand, i sent you what was pictured today. You should have in 6-10 biz days. Cant wait to see it incorporated into open9x.

This is what u need right bertrand?

Same here. Bertrand, do u need an encoder? I have one and a hippo board ill send you.

Awesome thank you Brent!

John

I live in NC. Raleigh.

I sure wish somebody could help me with this. Id there anywhere i can send this board to get fixed?

Ok I traced the voltage coming in. I'm at 9.8 until I hit u7. Then I go down to 1.3. That is also what I measure at the input pin of the 3.3 regulator. I'm guessing U7 is bad? Should it be putting out 5 volts?

I've also got to figure out how to fix the missing pads.

Is this the correct datasheet for the main regulator on the Rev B?? I really messed up my board. I was assuming the middle post that connects to two different spots was ground, but now I'm not sure. I can't get my board to work after soldering back in the old regulator. Pretty bummed. https://docs.g...

Well that explains it! Thanks!

Im pretty sure i did the wrong one. So where on the board is the 5 volt? U4?

I need help here. I bought this: http://www.murata-ps.com/data/power/oki-78sr.pdf I assumed it was the one with the heat sink on it. So I took it off, and matched up the input ground pins, and soldered the murata on. I'm getting nothing. I hope I didn't damage the board. I have searched and searched...

Yep right again Bertrand. Thanks!

Does anyone know why the custom function play track setting, I can't select a different sound besides the first one (0000) on my SD card? On page 2 of my radio setup, I can select and play every song.

Got my voice and splash screen up!

http://www.youtube.com/watch?v=QSsFWvkI ... dEQjmdwoEQ

That was it! Thanks so much Bertrand! It is working fine now.... Just gotta figure out why my files on my SD card are playing OK in the SD card menu, but not on the play track custom function setting. It is stuck at the first track 0000 and I can't figure out how to change it... Thanks again bertran...

I've flashed modems, routers, and other 9x's with er9x, the er9xsky board is without a doubt the hardest thing i've ever flashed

Yes I have, it seems to be working. I think I finally got C9x working too, I just wasn't waiting long enough. It takes a few minues before it starts to write I see. Then I get a "Sam-Ba finished correctly" But still a blank screen when I turn on the remote. I have an SD card in the slot, i...

Yes I have, when I go to read/write a file, it just sits a 0%. I tried moving the samba folder into the c9x folder, that didn't seem to help.

Is there a way to correctly flash open9x with samba?

Ok thanks. Still not working. I just keep getting a blank screen when I power on. I even tried the ersky firmware, installed excatly like the wiki page. Its like ive toasted mu flash