Search found 38 matches

by iFeghali
Sat Aug 18, 2018 11:37 pm
Forum: Turnigy 9XR PRO radio
Topic: Wierd issue with right gimbal
Replies: 82
Views: 7578

Wierd issue with right gimbal

Ok I fixed my right gimbal by pulling it off the radio and pushing a little bit the elevator pot away from the gimbal. Then I pushed it back in. Recalibrate and works like a charm now.


Enviado do meu iPhone usando Tapatalk
by iFeghali
Fri Aug 17, 2018 11:03 am
Forum: ersky9xr
Topic: RX Failsafe
Replies: 10
Views: 431

RX Failsafe

He explained it just above. I’m pretty sure he did but my extremely limited experience in the matter didn’t allow me to understand. Let me put in points the information I got from his last post: 1) “send now” will send failsafe values to RX once 2) failsafe values stored in RX are lost after a powe...
by iFeghali
Fri Aug 17, 2018 10:16 am
Forum: ersky9xr
Topic: RX Failsafe
Replies: 10
Views: 431

Re: RX Failsafe

When “repeat send” is enabled the radio will keep sending failsafe values even during normal flight ? What’s the purpose?


Enviado do meu iPhone usando Tapatalk
by iFeghali
Fri Aug 17, 2018 10:10 am
Forum: Turnigy 9XR PRO radio
Topic: Questions about RSSI
Replies: 7
Views: 364

Re: Questions about RSSI

He is asking if it is normal the RSSI dropping to zero when the RX and Radio are too close.. That should be normal as the RX is probably being swamped.. Signal is too strong. I have never seen it happening in range test mode though. :) João I can reproduce it consistently both in test range mode an...
by iFeghali
Fri Aug 17, 2018 10:08 am
Forum: Turnigy 9XR PRO radio
Topic: Questions about RSSI
Replies: 7
Views: 364

Re: Questions about RSSI

That is normal. The range check reduces the power to simulate a long distance. Move the radio 30 metres away with the model about 1 metre above the ground Check the RSSI value, a safe reading would be 45+. Got a 64 in plain sight and 45 behind a wall. Guess it’s good then. Enviado do meu iPhone usa...
by iFeghali
Thu Aug 16, 2018 11:48 pm
Forum: ersky9xr
Topic: RX Failsafe
Replies: 10
Views: 431

Re: RX Failsafe

Ok I got it. If anyone else is interested: 1) turn on RX 2) turn on TX 3) go to model setup -> protocol -> external -> long press failsafe 4) set mode to custom 5) set desired channel values or “use actual” 6) press send now (option will blink) 7) press the physical button in RX (the one used for bi...
by iFeghali
Thu Aug 16, 2018 7:34 pm
Forum: ersky9xr
Topic: RX Failsafe
Replies: 10
Views: 431

RX Failsafe

Hello

Where can I find documentation for failsafe menu under protocol (r221) for XJT ?

Didn’t find anything in the document “9XR PRO ERSKY9x explained”.

Thanks


Enviado do meu iPhone usando Tapatalk
by iFeghali
Thu Aug 16, 2018 7:19 pm
Forum: Turnigy 9XR PRO radio
Topic: Questions about RSSI
Replies: 7
Views: 364

Questions about RSSI

R221, menu protocol option “range test” gives me a number for RSSI. When close to RX (one or two feet away) I get a value of 90 but when too close (a couple inches) RSSI drops immediately to ZERO. Is this normal ? I know my critical alert is set to 42. Is a value of 90 when one feet away from RX goo...
by iFeghali
Wed Aug 15, 2018 2:29 am
Forum: ersky9xr
Topic: debug voice alert files
Replies: 4
Views: 137

Re: debug voice alert files

By the way Mike, I have noticed the voice pack for the latest firmware isn’t using the voice index as file names anymore. Can I still rely in the old voice index table (I.e. gear up = 76) ?


Enviado do meu iPhone usando Tapatalk
by iFeghali
Wed Aug 15, 2018 1:44 am
Forum: ersky9xr
Topic: Automatically generating voice alerts in Mac OS X
Replies: 1
Views: 118

Automatically generating voice alerts in Mac OS X

Inspired by this topic http://openrcforums.com/forum/viewtopic.php?f=64&t=6871 I decided to create a bash script that makes use of Mac OS X text to speech capabilities to automatically generate voice alert files. I am basically using 3 tools to generate the WAV file required by ersky9xr r221: say: c...
by iFeghali
Wed Aug 15, 2018 1:27 am
Forum: ersky9xr
Topic: debug voice alert files
Replies: 4
Views: 137

Re: debug voice alert files

Thanks it’s working now.


Enviado do meu iPhone usando Tapatalk
by iFeghali
Tue Aug 14, 2018 11:14 pm
Forum: ersky9xr
Topic: debug voice alert files
Replies: 4
Views: 137

debug voice alert files

hello i have generated the attached WAV files exactly the same way but 9XR Pro (r221) refuses to play one of them. learjet.wav is working, the other one isn't. learjet.wav: RIFF (little-endian) data, WAVE audio, Microsoft PCM, 16 bit, mono 16000 Hz File: learjet.wav File type ID: WAVE Num Tracks: 1 ...
by iFeghali
Mon Aug 13, 2018 9:07 pm
Forum: ersky9xr
Topic: Assign ID to exponential travel profiles
Replies: 9
Views: 283

Re: Assign ID to exponential travel profiles

Try: DrSw1 set as !IDv (!ID2) DrSw2 set as !ID^ (!ID1) In my opinion it will work better. I have just tried in Eepskye :) By the way, triple rates are explained on the Er9x manual, page 42 and 43. João Thanks. It’s clear now. For anyone interested that’s the relevant part: Hi is DrSw1 OFF (DrSw2 do...
by iFeghali
Mon Aug 13, 2018 9:50 am
Forum: ersky9xr
Topic: Assign ID to exponential travel profiles
Replies: 9
Views: 283

Re: Assign ID to exponential travel profiles

MikeB wrote:DrSw1 needs to be !ID^ (that is NOT ID^). When editing the switch value go DOWN to get the NOT switch values.

Mike
Thank you very much. Works like a charm :)


Enviado do meu iPhone usando Tapatalk
by iFeghali
Mon Aug 13, 2018 1:31 am
Forum: ersky9xr
Topic: Channel reversed ?
Replies: 0
Views: 93

Channel reversed ?

Moderator please delete this topic
by iFeghali
Mon Aug 13, 2018 1:18 am
Forum: ersky9xr
Topic: Assign ID to exponential travel profiles
Replies: 9
Views: 283

Re: Assign ID to exponential travel profiles

Set DrSw1 to !ID^ (!ID0) and DrSw2 to IDv (ID2). With the swith up you get high rate, in the centre you get mid rate and down gives you low rate. Mike That’s the first thing I tried mike, but unfortunately it didn’t work (or I’m doing it wrong). Doing as you said I get MID at the top and HIGH at mi...
by iFeghali
Sun Aug 12, 2018 1:39 am
Forum: ersky9xr
Topic: Assign ID to exponential travel profiles
Replies: 9
Views: 283

Re: Assign ID to exponential travel profiles

You mean something like a triple rate but with Expo only? João? Nope. I know I can set set 3 profiles for EXPO for each channel. So I can have a LOW EXPO, MID EXPO and HIGH EXPO for each channel. I can then assign TWO buttons to switch between those 3 profiles. If I use two normal switches they giv...
by iFeghali
Sun Aug 12, 2018 12:33 am
Forum: ersky9xr
Topic: Trim problem
Replies: 21
Views: 1201

Re: Trim problem

jhsa wrote:Probably Monday radios.
That’s interesting. We would call that a “Friday’s radio” here, since people are eager to get back home for the weekend and prone to make mistakes.



Enviado do meu iPhone usando Tapatalk
by iFeghali
Sun Aug 12, 2018 12:29 am
Forum: ersky9xr
Topic: Assign ID to exponential travel profiles
Replies: 9
Views: 283

Assign ID to exponential travel profiles

Hello

Is there a way to assign the 3 position switch “ID” to exponential travel profiles in the following way:

ID- > LOW
ID > MID
ID+ > HIGH

?


Enviado do meu iPhone usando Tapatalk
by iFeghali
Sun Aug 12, 2018 12:17 am
Forum: General Information & Rules
Topic: Problem with forum. Repeatedly "signed off"
Replies: 26
Views: 1358

Re: Problem with forum. Repeatedly "signed off"

bob195558 wrote:I am running Win7 64bit desktop PC, could the random Signed Offs be only with Win10 desktop PCs ?
Nope. I run Linux.


Enviado do meu iPhone usando Tapatalk
by iFeghali
Sat Aug 11, 2018 1:40 am
Forum: General Information & Rules
Topic: Problem with forum. Repeatedly "signed off"
Replies: 26
Views: 1358

Re: Problem with forum. Repeatedly "signed off"

bob195558 wrote:Could this be a EU area problem, as I am in the USA and seem to not be having this problem.

I’m in South America and that happens all the time to me when reading the forum trough the web. Never had any issue with Tapatalk though.


Enviado do meu iPhone usando Tapatalk
by iFeghali
Sat Aug 11, 2018 1:33 am
Forum: The Pickled Gnu (The Pub)
Topic: Flash lights on release of servo - Bait Boat Help
Replies: 54
Views: 1080

Re: Flash lights on release of servo - Bait Boat Help

Sounds like a good job for an Arduino


Enviado do meu iPhone usando Tapatalk
by iFeghali
Tue Aug 07, 2018 1:29 am
Forum: Turnigy 9XR PRO radio
Topic: Wierd issue with right gimbal
Replies: 82
Views: 7578

Re: Wierd issue with right gimbal

Mode 2. Only right gimbal has issues but if I’m gonna replace anything I would replace both of them and for something with better quality and easy to install. I guess it’s too much to ask :/


Enviado do meu iPhone usando Tapatalk
by iFeghali
Fri Aug 03, 2018 8:46 pm
Forum: Turnigy 9XR PRO radio
Topic: Wierd issue with right gimbal
Replies: 82
Views: 7578

Re: Wierd issue with right gimbal

Ok, check if the case of the pot is moving on the gimbal.. It has happened and the fix is to somehow glue the pot case to the gimbal. then calibrate the sticks again. It might not be the issue, but its worth check. you could use hot glue for example, if that is the case.. João Please check this.. J...
by iFeghali
Fri Aug 03, 2018 8:45 pm
Forum: Turnigy 9XR PRO radio
Topic: Wierd issue with right gimbal
Replies: 82
Views: 7578

Re: Wierd issue with right gimbal

By the way, if the pots are low quality can’t we just replace them for a better one instead of the whole thing ?


Enviado do meu iPhone usando Tapatalk
by iFeghali
Fri Aug 03, 2018 8:44 pm
Forum: Turnigy 9XR PRO radio
Topic: Wierd issue with right gimbal
Replies: 82
Views: 7578

Re: Wierd issue with right gimbal

I’m not sure I was clear enough. My problem is not a software or electrical issue. It’s mechanical. I can see the right stick struggling to move back from top to center. I believe it’s either the spring (I suppose there’s one) or something is sticky.


Enviado do meu iPhone usando Tapatalk
by iFeghali
Thu Aug 02, 2018 2:41 pm
Forum: Turnigy 9XR PRO radio
Topic: Wierd issue with right gimbal
Replies: 82
Views: 7578

Re: Wierd issue with right gimbal

Did you try calibrating your radio's gimbals? Please go to "Radio Setup / Calibration" select it, and follow the on screen instructions.. João Yes I did. But the right gimbal behaves differently in the upper and lower parts. Sometimes it sticks up and takes more time to center. Enviado do meu iPhon...
by iFeghali
Thu Aug 02, 2018 2:15 am
Forum: Turnigy 9XR PRO radio
Topic: Wierd issue with right gimbal
Replies: 82
Views: 7578

Re: Wierd issue with right gimbal

Well. I just spoke with hobbyking (livechat) they are sending me a new one. I dont even have to ship this one back to them!! woohoo. But I read that people put the aurora 9 gimbals in this thing. I will prolly end up doing that. I really like this radio. Couldn't ask for more. I have taken a vow to...
by iFeghali
Wed Aug 01, 2018 10:55 pm
Forum: Turnigy 9XR PRO radio
Topic: 9XR Pro and Simulators
Replies: 6
Views: 240

Re: 9XR Pro and Simulators

Ok, thanks again João I didn’t had to buy new accessories :) USB cable plugged in, radio calibrated, Aerofly RC7 bought from the Mac App Store. Only the sticks are working though, no buttons or pots. But that’s already a very good start. https://uploads.tapatalk-cdn.com/20180801/5cc2b5ca1ab9e7a4a3bd...
by iFeghali
Wed Aug 01, 2018 7:21 pm
Forum: Turnigy 9XR PRO radio
Topic: 9XR Pro and Simulators
Replies: 6
Views: 240

Re: 9XR Pro and Simulators

that's the only simulator I found for the mac:

https://www.ikarus.net/en/

Go to advanced search