openrcforums

maybe is FROS problem,use opentx all ok .use FROS 1505 FW
define MVOLT_AT_ZERO_AMP can't use 620,only can on 600 an if 610 sometime will error,but on opentx all ok

i change X12S use opentx 2.2 all become ok ,now can change MVOLT_AT_ZERO_AMP to 620 no error.

maybe this is FROS Problem !
try use opentx 2.2

i check ACS Vo on 0 Amp is 0.6 V,i think is unidirectional sensor

my current + temperature sensors temperature use A2 i check ACS 758 VCC is 5.01V,but if me change (define MVOLT_AT_ZERO_AMP) to 620,will error // ***** 2.1 - Frsky data ***** //#define VFAS_SOURCE VOLT_1 //#define FUEL_SOURCE ADS_VOLT_1 //#define A3_SOURCE ADS_VOLT_1 //#define A4_SOURCE ADS_VOLT_3 /...

// ***** 6.2 - Voltage parameters ***** #define PIN_VOLTAGE 2 , 8 , 8 , 8 , 8 , 8 // Fill 6 values; set to 0 up to 7 for analog pins A0 up to A7 ; set the value to 8 for the voltage(s) not to be measured. #define RESISTOR_TO_GROUND 0 , 0 , 0 , 0 , 0 , 0 // set value to 0 when no divider is used for ...

ACS Vo to A6, RAW 6.4v,ACS VCC to arduino Mini Nano 5V

// ***** 6.1 - Voltage Reference to measure voltages and current ***** //#define USE_INTERNAL_REFERENCE // uncomment this line if you use 1.1 volt internal reference instead of Vcc (voltage divider mst be used to reduce voltages to 1.1 volt max) //#define USE_EXTERNAL_REFERENCE // uncomment this lin...

Why can't I change to ten digits in (define MVOLT_AT_ZERO_AMP)? If I set it to 600, I normally say A in TX, but when I change to 620, there is a problem. In TX, it means 294996736.0 A. The value in consump is 238565. But it changes to Only one hundred digits. It is normal to connect to (efine REFERE...

Why can't I change to ten digits in (define MVOLT_AT_ZERO_AMP)? If I set it to 600, I normally say A in TX, but when I change to 620, there is a problem. In TX, it means 294996736.0 A. The value in consump is 238565. But it changes to Only one hundred digits. It is normal to connect to (efine REFERE...

can use on X12S use FROS ?

ACS758 50A Vo pin need add Capacitor to GROUND ? i only add 0.1uF vcc to GROUND.

Kilrah wrote: ↑Tue May 15, 2018 9:25 am It makes little sense to use 2. Just use one that works well.

I don't think FrOS supports multiple sensors of the same type anyway.

I think that you are correct. If use 2 sensors, they may make problems with each other due to errors.

I do not know if my understanding is correct or not. Two sensors are required to compensate for the error, but one processor is required ?

because i have FrSky Vario H,want add together use,i think two sensors Comparable will good than 1 sensor ?

i use FROS

https://www.youtube.com/watch?v=alZfqbgxtBc
today i try gy86 + frsky vario Vari-H

two sensors use,GY63 vario + frsky vario Vari-H
https://youtu.be/Q20AG9iy07A

how can see frsky vario Vari-H ID?

frsky vario Vari-H Buy it back. No change any.

only conect frsky vario Vari-H sersor no change to 0m ?

two sensors together use

i check oXs_config_advanced.h gy63 ID is 0,an frsky vario Vari-H ID is 0,why can use together ? frsky sensors ID download/file.php?id=6955&sid=078618554 ... 778421683f

or CSB to PS ?

gy 63 CSB pin to VDD ?

if i conect 2 gy 63 on 1 pro mini need set different 12C ID ?

Telemetered numerical values, better than using one

OXS gy63 is use normal set,and frsky vario Vari-H sensori no set ID use normal

before use GY63 on frsky X8r it ok,yesterday think i have frsky vario Vari-H sensor ,try connect 2 sensor,is work and work fine .... 2 sensor ID is different ???