Search found 8 matches
- Tue May 19, 2020 11:19 pm
- Forum: openTx
- Topic: Graupner using multi protocol and external telemetry
- Replies: 6
- Views: 5220
Graupner using multi protocol and external telemetry
I have the RadioMaster TX16S and bound up some Graupner Hott receivers. The LUA script is impressive how you can view and change your settings like a Graupner radio does. My issue is the vario and possibly other sensors. I have a two Hott receivers one with an internal vario and a GR-16L with an ext...
- Sat Nov 17, 2018 11:42 am
- Forum: openTx for FrSky radios
- Topic: Vario tones not working
- Replies: 3
- Views: 6272
Re: Vario tones not working
You don't have to copy anything my settings were wrong. You want to use Vspd, not Vario for the tones.
- Sat Jul 14, 2018 1:51 am
- Forum: FRSky Horus radio
- Topic: Slider pot, can I get one without the center bump?
- Replies: 0
- Views: 2739
Slider pot, can I get one without the center bump?
I don't like the bump in the center of the side slider on the X10S. I use that control for my sailplane flaps I find the bump very clunky. Does anyone know of a replacement POT that does have the center bump?
- Sat Jun 16, 2018 11:11 pm
- Forum: openTx for FrSky radios
- Topic: Vario tones not working
- Replies: 3
- Views: 6272
Vario tones not working
There is a topic on RCG where the vario tones don't work if you built the model with a different receiver and then switched to the GRX8. I started with a S8R RX for my glider, switched to the G-RX8, rediscovered the sensors but you cannot get the vario tones to work correctly. The only solution this...
- Fri May 04, 2018 9:30 pm
- Forum: openTx for FrSky radios
- Topic: Newbie help, servos won't travel past ~50%
- Replies: 8
- Views: 7194
Re: Newbie help, servos won't travel past ~50%
I just Googled what a STK is. It's a shame the radios don't come with the basics. I don't have one. Are there any other tools/dongles I should get? My primary interest is sailplanes (no gyro RX) and 3D foamies (Gyro RX). I will want talking varios for my sailplanes and from what I read the G-RX8 has...
- Fri May 04, 2018 7:46 pm
- Forum: openTx for FrSky radios
- Topic: Newbie help, servos won't travel past ~50%
- Replies: 8
- Views: 7194
Re: Newbie help, servos won't travel past ~50%
I assumed it was off since wiggling the RX around did not move the servos. The good news is a G-RX8 receiver showed up today in the mail and it travels the full range of the sticks. So I need to learn the radio and the gyro RX is probably not the place to start. Thanks for help Mike, I will be back ...
- Fri May 04, 2018 10:45 am
- Forum: openTx for FrSky radios
- Topic: Newbie help, servos won't travel past ~50%
- Replies: 8
- Views: 7194
Re: Newbie help, servos won't travel past ~50%
The gyros are not enabled.
- Fri May 04, 2018 3:51 am
- Forum: openTx for FrSky radios
- Topic: Newbie help, servos won't travel past ~50%
- Replies: 8
- Views: 7194
Newbie help, servos won't travel past ~50%
I'm stuck. I have a S8R receiver bound and 4 servos hooked up to a X10s. Thr, Rud, Ail will not use the full range of the sticks. The servo stops moving after about 50% stick travel, if you keep moving the stick past 50% the servo does not move. The Elev behaves normally. I have run through the stic...