openrcforums

Tx is Taranis with latest firmware, Companion9x 1.52 Rev 2381. Running Windows 7 home premium 64 bit. I was able to connect a couple of weeks ago. I have since uninstalled Companion 9x and reinstalled it with no luck.

No answers here, Huh?

I have run into the same problem. 2 weeks ago I could connect and read the Tx. Today I get the same error as above...There must be a solution somewhere....What causes it? Driver? Conpanion9x?

Explain please or give me a place to read about this... Did you read the manual? http://www.open-tx.org/2013/08/22/opentx-frsky-manual-en/ Once you're done with telemetry and audio, read the "A few interaction examples" chapter. Yes, I have read the above materials thank you for the help....

Rob Thomson wrote:You can also on the 'telemetry' screen fast values to display on screen.

Sent from my GT-I9300 using Tapatalk

Explain please or give me a place to read about this...

You get low battery warnings out of the box. For everything else use the voice readout custom function to play a value. The easiest trigger is a button like the trainer switch. Or a logic expression like value falling below a certain threshold or timer. (Previous tab.) Written on my mobile. Please ...

What do you mean by 'use'? You should see the values in the telemetry screen on the main screen. (Long press some key. I forgot which) Perhaps you need to select the voltage source first in the telemetry screen of the model setup. And you should select the right threshold voltages for your battery....

I got my Smart port voltage sensor today..Plugged it in and I am fairly sure it is working, problem is I cannot find some kind of write up on haw to use it in the Taranis....Any help or info appreciated...

OK, a done deal. Had to reverse the Aileron and Rudder. Now need to set up the mode.

Kilrah wrote:You'll need to go in the mixer and arrange the control->channel mapping in the way that your Nano QX wants them. Normally TAER.

I have done that.

I am trying to get my Nano QX working with my new Taranis. I have the DMS2 module in the taranis and have gotten it bound. Some of the controls seem to work but on the wrong stick, also when the motor does start the only way to stop it is to turn off the taranis...Help Please.....

kaos wrote:use eepe. back up your 5 model tx eeprom to a eepe file, then open the new model eepe file and copy the mode to your original 5 model eepe file then burn the new 6 model to Tx.
Marry X'mas!

Thank you very much, that will really help..Merry Christmas and a Happy Health new year...

Can a single eep file be imported into and existing one without disturbing the models in it. I have 5 models programed into my 9x and would like to import the setting from another model into it. I hope that is clear... example 5 planes in Tx found a model template eep file for another model that I w...

Looking for a Ares Gamma 370 Template..

jhsa wrote:If you are using er9x on stock board the best is to use eepe instead of companion.. Nothing against companion, the guys are doing an excellent work with it, but might not be 100% compatible with er9x at the moment...

Yeah. you are right, think I will stay away from it for the time being...Thanks.

Could we have a few more details please. You have the stock board with a Smartieparts board (which version?) What firmware did you have stock, er9x, open9x? Just because the screen is blank, doesn't mean the processor is not powered, so you should still be able to get AVDUDE to talk to the board. O...

Must be one of those "I be wrong days" I just reconnected the tx to computer and launched Companion. I does read the tx. I do see bad characters in the file..but still no display on tx. I will rewrite a new file to it and see how it goes.

Uhm... I have never before heard of that being done to factory reset? Is that a stock firmware feature? Anyway... It sounds to me like your model epprom has in some way become corrupted. Does avr dude still confirm that it can write / read from the radio? If it can, I would create a blank epprom in...

Sorry, did not answer completely. Only running Smartiparts board.

Factory reset. Hold exit button, turn on power. This is where I got the "Loading model 02" message.

Not sure what happened but I was using companion software and had read the TX memory, made some changes and wrote it back. Write was successful. I noticed that the power was now off on the Turnigy. Tried to turn it on. (No go.). Figured battery was dead so charged it..Still nothing. Tried to do a fa...

I am using the Turnigy 9x running er9x with my V911 and V939 with no problems.

From what I am reading Option 3 will require me to remove the antenna (Unsolder the lead) and move to the module. This however is not a problem. I think I can handle that.
Thank you.

The Champ uses DSM2 protocol, so the Turnigy 9x with the regular Turnigy/FlySky module is not compatible. Option 1: Install a DSM module (such as the new Orange one from HobbyKing) in the rear slot. The trouble is that conflicts with the module I assume is already in there. It's not easily removabl...

OK, Dumb question of the day.(Senior Day). I have a Turnigy 9x, have a smartiparts board installed and running er9x. Is there any way to bind this to a Hobbyzone Chanp? I realize I will have to do some mods to TX, but exactly which mods? Inquiring minds need to know. Not only that but the original r...

I should be receiving my WL Toys V939 any day now. Has anyone got an EEpe file for the er9x? Also in loading the file into my Rx will it overwrite the existing file for my V911? I am using eepe.exe.

This link might help you: http://www.hacksmods.com/2012/06/wl-toys-v911-settings-for-er9x/ It looks like the channel order is Ail, Ele, Thr, Rud Then invert channel 2 (elevator) Turn on extended limits on the first page of the model settings. Then set the channel 3 limits to +/-125. You will also w...

I want to thank all that tried to help with this setup. I really appreciate it. I reflashed Tx with a different er9x version and a sample eepe file. All is well, I am flying again. Again thank you all.

nsf wrote:rx=receiver.
To post your file, in eepe, on the icons, select the one that looks a computer chip with a green arrow. to do this your radio must be connected to the computer. Just take the file that is now open on eepe and save it, and then post it here.

Was the T9X working with your V911 before you flash with er9x? I am not even sure the WL Toy v911 rx(receiver) is compatible with T9X. but you do get response from the er9x even though it is not the right stick movement. the rx is where you plug in your servo wires and ESC throttle plug into. I hav...