openrcforums

Thought I'd come back and give an update...thanks to all the help here I got my issues sorted out and have been flying my T-rex 600E with 9XR Pro/ERSKY9x, I have 8 flights on her and am doing figure 8's pretty sloppily but no crashes yet. Again, thanks for all the help.

jhsa wrote: ↑Mon May 01, 2017 12:11 pm Try creating a new eeprom in eepskye. does it work now?

João

Im currently using the eeprom you sent me in trex450-30-07.zip or does that .bin file not also contain the eeprom?

jhsa wrote: ↑Sun Apr 30, 2017 8:49 am Is eepskye simulator still not working?
João

Yes, the simulator in eepskye is still not working.

Go to the HELI menu and reverse the three entries. That will fix it. I went into HELI and reversed the three entries but it just makes the aileron and elevator sticks backwards but it fixes the blades pitch. FIXED: I went and reversed all the PITCH lines on CH11 to be -100 and now EVERYTHING is wor...

Ok, the zip file attached has an eeprom file with two models.. The channel order is AETR. Please try them and see if one of them work.. You will have to change the protocol to the correct one.. João I tried your zip file, both the trex450 and the TrexRTest had issues. for one when I moved the ailer...

Just a little note: CYC1 - Is the Ele, and it should control the rear servo CYC2 and CYC3 control the left and right servos. I changed CYC1 and CYC2 around in the radio and now all is correct except when I add throttle the pitch on the blades goes negative and vice versa when I reduce throttle. Wha...

Rake a tip though. Change it to a flybarless ASAP - you will NEVER want a flybarred heli again! Lol! I'm sure thats true but it was a matter of economics, I bought this heli from a friend for $275 and it was ARF with 4 Futaba servos, a Futaba GY611 gyro, Castle 1515/2.5D/F motor, 6S lipo pack, two ...

Using eePskye I created a new model, set protocol to "Multi", channels to 7, sub-protocol to DSM & DSMX-22, I then set the Option field from 0 to 7 because someone said that mattered. I did not need to use a template because the mixes were already there... CH01 +100%Ail CH02 +100%Ele C...

What is the exact heli are you attempting to setup? It is an older Align Trex 600 CF flybar with two servos up front and one in rear of the swash Tx = 9XR Pro with ersky9xr r220 firmware and a 4in1 Multi module set for DSMX Rx = Redcon CM703 7ch DSMX Spektrum clone with satellite The radio is mode ...

Just think - if you were using and FrSky receiver, all you would have are channel numbers to go by ... I did try this but some servos just didn't move the way they should have. Also, being a Spektrum Rx I'd like to find a way to get the throttle on ch1 so the built in fail safe would reduce the thr...

No...not sorted yet...I had it real close though but the pitch servo was turning the blades the wrong way, by reversing the servo it made the swash not turn correctly, then I reversed the AILE servo and it messed the whole thing up. The 4in1 manual says if i set my radio to AETR order that it will s...

I just found this... viewtopic.php?t=9298
This seems to be suggesting my 4 in 1 module has a set order that it needs. TREA order?
I will test this when I get home tonight.

jhsa wrote: ↑Tue Apr 25, 2017 5:04 pm . does your radio have throttle on the left or right?

João

It is a mode 2 with THR & RUD on left...I have also set it to mode 2 in the radio setup.

...and for anyone who was offended by my "maybe this radio needs to go in the trash can" comment, I didn't mean the 9XR was a junk radio, I've owned a 9X, 9XR and now this 9XR Pro so I do like these radios a lot...I meant that in as much as maybe I should trash it and buy another 9XR Pro.....

There is more going on here than just servo direction, I have verified both my AILE and my PITCH servo are plugged into the correct channel but then why is my ELEV servo moving when I move the sticks aileron left and right...and I don't mean it moves a little...it is moving 100% of its movement like...

More results from testing, I created a standard 4ch airplane mix and deleted everything but the rudder...then I moved it from ch1 to ch2 to ch3 to see what the results were. Ch1 in the radio moved the servo when attached to ch2 on the Rx. Ch2 in the radio moved the servo when attached to ch3 on the ...

That sounds odd. You normally need to set it to a specific value, or it is set when you bind in AUTO mode. The "default" is 0. Try setting it to 7, it was 0 in the EEPROM you posted. Using 8, or higher for "Option" causes a different mode of transmission as only 7 channels are s...

MikeB wrote: ↑Sun Apr 23, 2017 11:39 pm What about changing the Option value. The radio should display 4ch or 5ch etc. when you set it to 4 or 5 etc.
You probably need it set to 6 or 7.

Mike.

It sets to 8ch by default...I just leave it there.

Yeah, it works fine in eepskye. - There are a couple things you can test. connect it to the sim with that model loaded. Do ch2 and 6 work then? - Create a new model, do the channels work?? João Im not sure how that would work since I dont think the sim uses the CCPM mixing in the radio and the CCPM...

I loaded your EEPROM into eepskye and I see the protocol set to MULTI/AUTO, with the Option set to 0. When you bind, provided you have the telemetry settings correct to be able to receive data from the Multi module, these should change to the settings needed for your receiver. If they don't change,...

Is anyone with a 9XR Pro radio willing to try my EEPROM out and see if I set something up wrong please?

I emailed jhsa the EEPROM file so hopefully he can post it here for me so someone can take a look at it.

Thanks.

Hmmm...it says ERROR: A PHP extension has stopped the file upload.
Same error with IE and Firefox

here is my EEPROM file from my 9XR Pro

Thanks.

I still have no idea whats going on...basically the radio is showing movement on Ch2 but the servo does not move. Same with Ch 6. RUD and ELEV move fine...same issue with three receivers. My radio setup is exactly like the link provided which shows a JR/Spektrum setup in TAER order. The radio was pu...

Thank you Daedalus66 ...I wish I could have found that thread while I was searching for help setting up my radio! ...ill know tonight if this solves my problem.

It's an older flybar Align T-Rex with one servo in back (ELEV) and two up front, the left servo is PITCH and the right servo is AILE. Best I can tell so far is that the Heli Template did not set the mixing up correctly because in the simulator there are servos moving that I dont think should be movi...

The radio is correctly set to mode 2

I bought a used T-rex 600, complete minus receiver, I have a spektrum receiver and its order is labeled TAER on it, so I went into my 9XR Pro running r220 ersky9xr and I set the radio up for TAER, then I used the template to create a helicopter mix but the mix is being created like this..... ch1,2,3...

SOLVED: thanks for the help guys ...I was able to verify last night that putting the radio back to AETR did fix the issue. Once I selected the DSM protocol in the Multi RF module then it sends the spektrum TAER order to the receiver. THIS FORUM ROCKS!