openrcforums

The cut cable seemed like it got hot and cut from the board.

Στάλθηκε από το Redmi Note 3 μου χρησιμοποιώντας Tapatalk

Στάλθηκε από το Redmi Note 3 μου χρησιμοποιώντας Tapatalk

I unscrewed the smartieparts board and i saw something wrong. A cable from the board was cut. I solder it but still nothing. The board doesn't seem to have a problem. And now I'm not sure if i took out the DJT with the tx switched on at the first place. Something else is wrong. Στάλθηκε από το Redmi...

I have the cables from the tarot fc to the receiver but the camera is pluged directly to rx

Στάλθηκε από το Redmi Note 3 μου χρησιμοποιώντας Tapatalk

The leds on ths DJT and receiver were EXACTLY as you drscribed.
It


Στάλθηκε από το Redmi Note 3 μου χρησιμοποιώντας Tapatalk

My turnugy is the old one which i hade to solder to connect the smartieparts. Is it possible that has to do with this or something moved and doesn't make good contact at the back of smartieparts?

Sent from my Samsung Galaxy Note 10.1 edition 2014

The second method with the GND to resistor seemed to work. It didn't flash the green led on the quad but red (searching for satellite), but i couldn't control it(couldn't arm the motors). I tried the bidding method you suggested and everything was as you said(the leds) but again the green light of t...

Ok I see

Στάλθηκε από το Redmi Note 3 μου χρησιμοποιώντας Tapatalk

Ok, thanks. I'll do it on Sunday evening as tommorow i'm on duty at my job.
What is the expansion grid? Which is the ppm signal?
Sorry for my questions but i haven't got much experience

Sent from my Samsung Galaxy Note 10.1 edition 2014

Sent from my Samsung Galaxy Note 10.1 edition 2014

Sent from my Samsung Galaxy Note 10.1 edition 2014

And i took some more pics, maybe you see something wrong

Sent from my Samsung Galaxy Note 10.1 edition 2014

Sent from my Samsung Galaxy Note 10.1 edition 2014

Sent from my Samsung Galaxy Note 10.1 edition 2014

Sent from my Samsung Galaxy Note 10.1 edition 2014

Nothing wrong.

Sent from my Samsung Galaxy Note 10.1 edition 2014

Nothing wrong.

Sent from my Samsung Galaxy Note 10.1 edition 2014

Besides my other turnigy transmitter (without 9xtreme) binds fine.

Everything is as you say with the only difference here '' Turn on the Tx. When all alarms are cleared, the RED led on the DJT is ON, the green led is flashing fast. On the V8FR, the RED led is on solid, the green led is off (or may just be very very dim).'' the green led isn't flashing fast on the D...

How can i format the tx? And then install the rom again?

Sent from my Samsung Galaxy Note 10.1 edition 2014

I'm a little bit away from buying a taranis but i've already spent some money AND work time at this tx and i love it, so I can't give up yet.

Sent from my Samsung Galaxy Note 10.1 edition 2014

This is what it does. Not the fast blinking of the green light which is failsafe.

Sent from my Samsung Galaxy Note 10.1 edition 2014

Sent from my Samsung Galaxy Note 10.1 edition 2014

When i move the sticks the numbers at the bottom change

Στάλθηκε από το Redmi Note 3 μου χρησιμοποιώντας Tapatalk

https://vimeo.com/177676820

Στάλθηκε από το Redmi Note 3 μου χρησιμοποιώντας Tapatalk

Ok, got it

Στάλθηκε από το Redmi Note 3 μου χρησιμοποιώντας Tapatalk

So the one jack goes to the trainer port and to the other side i connect one cable(which of two as the jack will give me two cables?) to the Rxd pin on the module. Is that right?

So we want a jack to jack cable. I'll make one tomorrow. After i make it what will i do? Where do i put the second jack? Thanks

Switched on tx

Στάλθηκε από το Redmi Note 3 μου χρησιμοποιώντας Tapatalk