openrcforums

Some-how the speaker was broken and it was also strong that the resistance of the speaker was way to high so something might have happened... But I have not done anything to harm it. Hmm, but I just got a toy and used its speaker.

NEW EDIT!!!!!!!

SO GUYS I CAN CONNECT MY TX TO MY COMPUTER NOW AFTER STEVE SENT ME THE USB HEADER NOW I WILL DIAGNOSE THE SPEAKER PROBLEM

There may be more than one problem here. Let's check the audio. 1. Create a new model and have it as the selected model, don't change any values. 2. Check the volume is set to something other than 0 (e.g. 2). 3. In the model, set up a new Voice Alert: Switch RUD Trigger ON File Type AUDIO Voice Fil...

Check the USB connector is fully inserted on the board. Also check the little micro USB connector for bad soldering on its pins. If you are good with a soldering iron you could try to touch the pins and reflow the solder, but it isn't an easy job. At this point perhaps the best option is to contact...

My speaker also has a resistance of 13ohms, so I think the speaker is fine.

Kilrah wrote:

HAILME123 wrote:(like I said, I think the usb is fine, because ^^^)

HAILME123 wrote: There are two tones on the PC, then I get a warning saying my device has malfunctioned

Actually this suggests there is a hardware issue in the USB lines on the board.

Is there a way to fix this and the sound issue?

Try different cables anyway. I have cables that work with some devices, but not with others. João I am using the same cables that I used before to flash my TX. I have literally wasted all my ideas. (I went on the 9xtreme website and attempted the method without pinching) I opened up the TX tried co...

Try different cables anyway. I have cables that work with some devices, but not with others. João I am using the same cables that I used before to flash my TX. Thanks anyways. I have literally wasted all my ideas. (I went on the 9xtreme website and attempted the method without pinching) I opened up...

On the version screen, what revision number is shown on the SVN line? If you have upgraded the firmware from the original as shipped you may have the joystick support in. Please try the following (to test the USB). Start the radio normally. Now plug the USB cable in. If the firmware is recent enoug...

Please start the radio in bootloader mode. Next connect the USB to your PC. 1. Does the radio show "Connecting..." on the display? 2. Does the PC sound the tones indicating a USB device has been connected? 3. If so, does "My Computer" show two drives have been found? 4. Does the...

Yes. Three in fact. The transmitter is not even recognised by the computer. (when I checked my system information and device manager on my mac and PC)

Thanks for the reply.

I did that and I still get TX not mounted.

PLEASEEE HELLP ALL DEVELOPERS AND ANYONE WHO HAS SUPERIOR KNOWLEDGE AND EXPERIENCE!!! I think I have found an issue in the 9xtreme board, and it is very, very frustrating. Ok so I woke up early in the morning to fly my quadcopter. Went to the park, turned on my transmitter. Hmm... something strange ...

So all I need is voltage and RSSI from y quad (I have DJT module and reciver) I just want to be able to fly my quad and no how to change the sub trim and all that.

Hello guys, I am familiar with the original turnigy 9x interface, however, I have just recently moved my TX with the 9xtreme, and updated it with version 218. However, since all my settings are not there anymore, can anyone tell me how you can setup the er9sky firmware for a quadcopter.

Thanks for the post

Hello Bob. Can you use RSSI with a compatible receiver in the connection you have shown (because it seems so simple, no soldering required :D )? And I have heard that you use the metals tabs in the Tx compartment holder of the 9x and you can solder some wires in the DJT in order to use this tabs, so...

Hi HAILME123, For more information about external DJT module Telemetry connections, see here: (http://openrcforums.com/forum/viewtopic.php?f=126&t=8506). Also see 9Xtreme Connecting XJT Module , which has some of the same info for the DJT module: (http://openrcforums.com/forum/viewtopic.php?f=1...

Thanks for your contribution. Now I can use the DJT (Non-do it your self module) I was a little bit shaky before you guys answered. Thanks!

I am sorry for this question but I have just begun RC and 14 years of age.. Help me out :D :D I currently believe that the 9Xtreme board is restricted to the ERSKY9X firmware. Is the DJT Frsky transmitter module restricted on any features due to this firmware, such as the two way antenna, where you ...